10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
2. IP Networking
I am am using IPv6 IP's with an OS of Debian.
Is it possible to set a *static* default gateway w/o the router being connected? Will that gateway change when the router is connected?
TIA (0 Replies)
Discussion started by: Meow613
0 Replies
3. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
4. Solaris
Hi all,
Just now i had change the gateway for a server
Go to /etc/defaultrouter, change to 10.86.33.1
route delete default 10.86.39.222
route add default 10.86.33.1
now cannot telnet to the server already..
any idea? (5 Replies)
Discussion started by: SmartAntz
5 Replies
5. AIX
Dear folks,
How can delete the gateway from smitty or by command, Because I have 2 gatway in the system and I tried to delete by smitty it gave me failed command (7 Replies)
Discussion started by: magasem
7 Replies
6. Programming
how we can get the gateway address.
i know gethostname used for ipaddress
how we can get the system gateway address.
thank u inadvance,
sree (2 Replies)
Discussion started by: phani_sree
2 Replies
7. Shell Programming and Scripting
Hi,
I have a challenging task,in which i have to find the duplicate files by its name and size,then i need to take anyone of the file.Then i need to open the file and find for more than one pattern and count of that pattern.
Note:These are the samples of two files,but i can have more... (2 Replies)
Discussion started by: jerome Sukumar
2 Replies
8. Red Hat
Hi,
in which file and how shuold be decalred a gateway and its IP adresse ?
Where and how add a gateway ?
Many thanks before. (3 Replies)
Discussion started by: big123456
3 Replies
9. IP Networking
I used "route" to add the default gateway
I wrote this:
route add default 19x.x.x.x 0
but this is not permanent default gateway.
Do I need to use another command?
Thank a lot (2 Replies)
Discussion started by: lmena
2 Replies
10. UNIX for Dummies Questions & Answers
hi
i got a problem. I use a fbsd box to share my (DSL)internet connection.
I got 2 networkcards in my fbsd box, but my networkcard 1 (to my modem) always go out. the led don't burn anymore and I lose my connection to the internet :(
but my networkcard2 (to my local network) doesn't go out,... (2 Replies)
Discussion started by: Stormpie
2 Replies
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-m hoplimit
Specify maximum hoplimit.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
RETURN VALUES
The traceroute6 command will exit with 0 on success, and non-zero on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
May 17, 1998 BSD