10 More Discussions You Might Find Interesting
1. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
2. UNIX for Dummies Questions & Answers
Hi Guys,
I m using redhat 6, I have installed root partition as non-LVM .
Is there any way i can convert it to LVM? (1 Reply)
Discussion started by: pinga123
1 Replies
3. AIX
Hello!
I did a big mistake and now I have to change the ODM base manually :wall:
I had a server of test with 2 VG (rootvg and datavg). I had to test something on it with an other AIX version. So, to be sure to restore it, i did a mksysb before but I had completly forgotten the second vg and... (1 Reply)
Discussion started by: Castelior
1 Replies
4. AIX
Please consider this a question about basics&best practices. On AIX 5.3 system, three raw physical volumes are defined from storage. While doing a read with command dd from the raw device, the speed rate is 250Mb/s.
Then, it gets complex when I define these three pv's to an lv of type raw. Doing... (4 Replies)
Discussion started by: royalliege
4 Replies
5. AIX
Hi,
I gonna try to explain my problem.
When I list my tty I have something like that:
sa3 is the RAN where the tty are connected.
Yesterday I tried to delete every tty from the RAN
I had a problem with a tty which was not possible to delete with rmdev -dl, so I had to :
- delete it... (0 Replies)
Discussion started by: Castelior
0 Replies
6. HP-UX
Hi,
I'm new to HP-UX.
I have LVM on /var with 92Gig. I would like to reduce it to create another LVM for Oracle client with 800 meg or so. How to do it. I'm running 11.iv3
Thanks (4 Replies)
Discussion started by: lamoul
4 Replies
7. AIX
Hi All,
I remove the default gateway by using a command line but I need also to remove it from ODM so that reboot will not trigger it back.
How do I remove it from ODM of AIX 5.3?
Thanks for any comment you may add. (4 Replies)
Discussion started by: itik
4 Replies
8. AIX
Hi Everyone,
I would like to know if its possible to create a 2 copy mirror using LVM with 1 member a FC attached disk and the other an iscsi disk.
Will LVM let me mirror to two different disk types?
I know there will be issues doing this however it is only a short term solution until we... (1 Reply)
Discussion started by: bizman
1 Replies
9. AIX
I have replace a couple of hdisks in and old AIX 4 system. I have them assigned to the hdisk numbers previously in the system. When I don an lsvg -p vgname, i see them old devices by device number still come up as missing. I think they are still in the ODM,, how can I remove them?
Thanks
Mike (5 Replies)
Discussion started by: mhenryj
5 Replies
10. UNIX for Advanced & Expert Users
I recently had a disk crash and was not able to clean the dump lv off the disk. Now trying to create new lvdump I am running into errors.
My question is how do I remove the old lv out of the ODM? I have tried going through smit and also just rmlv and it cannot find the lv. Yet when I run lslv on... (0 Replies)
Discussion started by: Wamland
0 Replies
Odm & Lvm