Hi guys,
I am currently runnig hp-ux v11.3. I have enabled auditing and I am able to send the audit events to a text file in syslog format using the following command:
audisp -r /var/.audit/audtrail/auditfile -P -o follow -O sync | audit_p2l > /var/adm/auditlog
I am required to send the... (0 Replies)
Hi everyone,
how i can configure a single audit service in the global zone for all zones, on solaris BSM.
I will be glad to hear back from you.
Thanks and Regards (3 Replies)
Dear All
When I start the AIX(6100-06)audit subsystem.
the log will save in /audit/stream.out (or /audit/trail), but in default when /audit/stream.out to grow up to 150MB.
It will replace the original /audit/stream.out (or /audit/trail).
Then the /audit/stream.out become empty and... (2 Replies)
Hi there,
I want to enable auditing for the following events in a critical AIX UNIX server by editing the /etc/syslog.conf file:
Authentication events (login success, login failure, logout)
Privilege use events (change to another user etc.) ... (1 Reply)
AUDITD(8) System Administration Utilities AUDITD(8)NAME
auditd - The Linux Audit daemon
SYNOPSIS
auditd [-f] [-l] [-n] [-s disable|enable|nochange]
DESCRIPTION
auditd is the userspace component to the Linux Auditing System. It's responsible for writing audit records to the disk. Viewing the logs is
done with the ausearch or aureport utilities. Configuring the audit rules is done with the auditctl utility. During startup, the rules in
/etc/audit/audit.rules are read by auditctl. The audit daemon itself has some configuration options that the admin may wish to customize.
They are found in the auditd.conf file.
OPTIONS -f leave the audit daemon in the foreground for debugging. Messages also go to stderr rather than the audit log.
-l allow the audit daemon to follow symlinks for config files.
-n no fork. This is useful for running off of inittab
-s=ENABLE_STATE
specify when starting if auditd should change the current value for the kernel enabled flag. Valid values for ENABLE_STATE are "dis-
able", "enable" or "nochange". The default is to enable (and disable when auditd terminates). The value of the enabled flag may be
changed during the lifetime of auditd using 'auditctl -e'.
SIGNALS
SIGHUP causes auditd to reconfigure. This means that auditd re-reads the configuration file. If there are no syntax errors, it will proceed
to implement the requested changes. If the reconfigure is successful, a DAEMON_CONFIG event is recorded in the logs. If not success-
ful, error handling is controlled by space_left_action, admin_space_left_action, disk_full_action, and disk_error_action parameters
in auditd.conf.
SIGTERM
caused auditd to discontinue processing audit events, write a shutdown audit event, and exit.
SIGUSR1
causes auditd to immediately rotate the logs. It will consult the max_log_size_action to see if it should keep the logs or not.
SIGUSR2
causes auditd to attemp to resume logging. This is usually used after logging has been suspended.
FILES
/etc/audit/auditd.conf - configuration file for audit daemon
/etc/audit/audit.rules - audit rules to be loaded at startup
NOTES
A boot param of audit=1 should be added to ensure that all processes that run before the audit daemon starts is marked as auditable by the
kernel. Not doing that will make a few processes impossible to properly audit.
The audit daemon can receive audit events from other audit daemons via the audisp-remote audispd plugin. The audit daemon may be linked
with tcp_wrappers to control which machines can connect. If this is the case, you can add an entry to hosts.allow and deny.
SEE ALSO auditd.conf(5), audispd(8), ausearch(8), aureport(8), auditctl(8), audit.rules(7).
AUTHOR
Steve Grubb
Red Hat Sept 2007 AUDITD(8)