8 More Discussions You Might Find Interesting
1. Solaris
Hi
I am having two node cluster. I was trying to change the to use scsi3 reservation for all disks having two paths. Please let me know where I went wrong or there any issue to implement the same.
On node1
bash-3.2# cldev status
=== Cluster DID Devices ===
Device Instance ... (8 Replies)
Discussion started by: sb200
8 Replies
2. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
3. Red Hat
Hi,
I would like to know scsi id of hard drive, which command is used to find scsi id of hard drive and disk related information.
Regards
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
4. UNIX for Dummies Questions & Answers
hey guys this is my problem I have SCO unix installed on a IDE h/drive. I want to add a SCSI hard drive, how do i do that within UNIX (1 Reply)
Discussion started by: kwame.neilsen
1 Replies
5. Solaris
I have run init 0 to bring it to OK prompt.
I know that probe-scsi-all can hang the system.
I want to know what is the difference between probe-scsi-all and probe-scsi.
I was told that probe-scsi-all external and internal devices and probe-scsi shows only internal devices. what dose this ... (3 Replies)
Discussion started by: nitinkgoud
3 Replies
6. UNIX for Advanced & Expert Users
I would like to install a AIT drive to the scsi connector on our solaris box. I am very new to the unix world and would be greatful if someone could help or lead me in the right direction.
Thanks (4 Replies)
Discussion started by: vpyle
4 Replies
7. UNIX for Dummies Questions & Answers
Hello agian !
What is the difference between SCSI and IDE hard disks ?
I have Intel PC and when i check i have Generic IDE TYPE DISK0
is IDE hard disk is ok for Solrais ? or should i buy the SCSI hard disk ?
Thanks
Abid Malik (3 Replies)
Discussion started by: abidmalik
3 Replies
8. UNIX for Advanced & Expert Users
How can you get a scsi card to initalize or decome available at boot up on AIX 4.3 (1 Reply)
Discussion started by: truma1
1 Replies
TRM(4) BSD Kernel Interfaces Manual TRM(4)
NAME
trm -- Tekram TRM-S1040 ASIC based PCI SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device trm
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
trm_load="YES"
DESCRIPTION
The trm driver supports PCI SCSI host adapters based on the Tekram TRM-S1040 SCSI ASIC.
HARDWARE
SCSI controllers supported by the trm driver include:
o Tekram DC-315 PCI Ultra SCSI adapter without BIOS and internal SCSI connector
o Tekram DC-315U PCI Ultra SCSI adapter without BIOS
o Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector
o Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS
o Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS
o Tekram DC-395U2W PCI Ultra2-Wide SCSI adapter with flash BIOS
For the Tekram DC-310/U and DC-390F/U/UW/U2B/U2W/U3W PCI SCSI host adapters, use the sym(4) driver.
SEE ALSO
cd(4), ch(4), da(4), intro(4), sa(4), scsi(4), sym(4)
http://www.tekram.com/
AUTHORS
The trm driver was originally written for FreeBSD 3.0/i386 by Erich Chen of Tekram Technology, and ported to FreeBSD 5.0 by Olivier Houchard
<cognet@FreeBSD.org>.
BSD
December 8, 2002 BSD
