Powervm ivm vios


 
Thread Tools Search this Thread
Operating Systems AIX Powervm ivm vios
# 1  
Old 03-26-2019
Powervm ivm vios

Hello,

After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )

i get this message

Code:
"I/O hosting requires a hosting partition - boot not permitted".

HMC was connected to the machine
then HMC was removed through ASMI

Searching on google found this
Quote:
I/O hosting requires a hosting partition - boot not permitted
exit called ok

This happened with me when I created an AIX LPAR, but a VIO image was installed on the disk, where I wanted to boot from.
(When there is a mismatch between the LPAR type and the booting image this error will pop up....I guess.)
But doesn't mention solution,
how can one solve "mismatch between the LPAR type and the booting image"
# 2  
Old 03-26-2019
Quote:
Originally Posted by filosophizer
how can one solve "mismatch between the LPAR type and the booting image"
hmm, just to make sure i understand the situation correctly:

- you have (POWER6) managed system
- you want to boot from an internal disk
- on the disk a VIOS image is installed

On the case of 3 "yes"es: you need to install the LPAR anyway, so boot it via NIM methods (mksysb+spot). You can the select the disk to install to and this disk will be wiped first, so the VIOS image will go away. Only then (after installation) you can boot from the disk.

I hope this helps.

bakunin
# 3  
Old 03-26-2019
Googled it, and many users have similar issues and no solution is posted:

here is the solution:
1) Check the firmware

2) Check if the machine has VET VIOS POWERVM IVM key license enabled

3) HMC should be disconnected from the machine

Code:
CoD Capability Settings 

Capability bit information	Capability bit status/count
0 AIX allowed (license needed)	False
1 AIX allowed (license not needed)	True
2 RPA I/O hosting	True
3 AIX diagnostics	True
4 Subprocessor partitioning	True
5 LPAR creation allowed	True
6 3D work-station graphics card OK	True
7 External GX busses OK	True
8 i5/OS partitions allowed	True
9 Limit the number of i5/OS processors allowed	False
10 Reserved	False
11 100% interactive	False
12 Memory bandwidth	False
16 Extreme boot capability	False
31 HV I/O allowed	True
32 Number of 5250 users	0


MAKE SURE TO REMOVE HMC from ASMI
Hardware Management Consoles 

 √	Connection Id	Address ( IP )	State
	7042CR4*107A0CB	Not Applicable	Temporary Disconnect


Hardware Management Consoles7042CR4*107A0CB: Successfully disconnected

Operation completed successfully

power down and power on the system and it should work

Last edited by filosophizer; 03-28-2019 at 05:04 AM..
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. AIX

Revisiting IBM PowerVM VIOS AIX

coming from this thread: https://www.unix.com/aix/211107-ibm-power-pseries-open-firmware-boot-vios-powervm-vet-code.html PowerVM, formerly known as Advanced Power Virtualization (APV), is a chargeable feature of IBM POWER5, POWER6, POWER7, POWER8, and POWER9 servers and is required for support... (0 Replies)
Discussion started by: filosophizer
0 Replies

2. AIX

AIX VIOS IVM Ethernet problem

Hi All, I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box. We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies

3. AIX

CD-ROM issue with PowerVM IVM VIOS

I am facing problems in moving CD-ROM from one lpar to another. CDROM can be seen on the POWERVM (IVM) server , but through the web-access if I move it ( assign it ) to LPAR it will be assigned. I run cfgmgr , and the cdrom does not show up in the LPAR. I firmly believe this is the reason why I... (2 Replies)
Discussion started by: filosophizer
2 Replies

4. AIX

IBM Power Pseries Open Firmware boot / VIOS POWERVM VET CODE

Hello, I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization. So when booted , it goes into OPEN Firmware I/O Hosting requires a hosting partition boot not permitted exit called > ok Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies

5. AIX

IBM VIOS POWERVM IVM error

Hi, When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error http://vioserver/j_security_check I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage. I... (2 Replies)
Discussion started by: filosophizer
2 Replies

6. AIX

VIOS IP address - separate vlan for vios servers ?

Hello, Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2. What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies

7. AIX

Need IBM PowerVM

Hi all please give me a link for IBM PowerVM (4 Replies)
Discussion started by: babinlonston
4 Replies

8. AIX

PowerVM HA questions

hi guys, i need to develop following setup for a customer: high availability oracle database on aix7 and linux in 2 different LPAR using dual ps700 blande a ds3400 and HMC. the question is, it is possible to have automatic vioc failover(aix,linux) when for example 1 vios goes down? in... (6 Replies)
Discussion started by: gullio23
6 Replies

9. AIX

VIOS IVM unavailable - how do I restart it?

Hi everyone, Sorry if this post is in the wrong place. I searched the forums for "IVM" and it turned up no results. Hopefully someone knows about this. My dilemma is that I have multiple IBM JS12 Express blades in our blade center, each running VIOS 2.1.0.10-FP-20.1 and hosting a couple LPARs. Out... (2 Replies)
Discussion started by: need2bageek
2 Replies

10. AIX

PowerVM Express and IVM limitations

When using PowerVM Express and IVM (no HMC) on a Power6 P520 , can I configure 2 LPARs in addition to a VIO server, or does the VIO Server count as one of the two LPAR's that PowerVM Express allows? (1 Reply)
Discussion started by: JodyTek
1 Replies
Login or Register to Ask a Question