10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Experts,
I hope I'm writing to the correct category for my question.
I have a very basic shell script for doing file archiving to the external usb hard drive (WD studio edition II 2TB formatted as FAT32 for compatibility). The shell script only needs to run once per day. It basically... (8 Replies)
Discussion started by: johankor
8 Replies
2. AIX
Can someone please help me understand what it is I am doing incorrectly?
I have 22 PVs (disks) assigned to a VG, the stats on the disks:
# lspv hdisk1
PHYSICAL VOLUME: hdisk1 VOLUME GROUP: vg_usr1
PV IDENTIFIER: 0000150179158027 VG IDENTIFIER ... (3 Replies)
Discussion started by: c3rb3rus
3 Replies
3. AIX
Hi,
How can we share a AIX drive on to Windows 2012 server. or vise versa.
Note: Not using NFS/CIFS/samba. (*we are not able to use samba/NFS/CIFS for some reason)
Requirement: How to have real time file sharing over the network between Windows and UNIX
Do you guys have any ... (4 Replies)
Discussion started by: System Admin 77
4 Replies
4. AIX
Hello!
I have a LPAR with 51GB RAM
topas shows 21% of memory for client pages (~11Gb)
svmon -G show 2906772 client pages in use (~11Gb)
but then i try to investigate per process client memory usage
svmon -P -O filtertype=client
and summarize inuse column, i get only 347880 pages... (1 Reply)
Discussion started by: sys
1 Replies
5. Solaris
Hello Gurus!!
Very recently i tried to mount a USB pen drive onto my solaris 10 (X4170 model) server. As i understand, in ideal scenarios it should get mounted automatically, but it did not happen. Neither anything is shown in "iostat -En" output or "rmformat -l" about the pen drive.
I also... (10 Replies)
Discussion started by: EmbedUX
10 Replies
6. UNIX for Dummies Questions & Answers
Hello
I want to connect a usd disk drive on HP server rp 2430 under Unix HPUX 11, the server does not have a usb port, I have a usb pci card I am not using, will it be possible to use it and connect a usb drive ? if yes what will be the steps to follow.
regards (0 Replies)
Discussion started by: simansou
0 Replies
7. UNIX for Advanced & Expert Users
We are using AIX 5.2 using jfs2 almost all excpt one mount.
Is it possible for a non root user id to mount one file system without journaling turned on, perform some activities and then remount (un-mount and mount) the same file system again.
Please advise if this is possible
Thanks (2 Replies)
Discussion started by: jerardfjay
2 Replies
8. SCO
Can anybody help me out to mount USB flash /floppy drive in sco openserver 6.0 . (5 Replies)
Discussion started by: sureshdrajan
5 Replies
9. AIX
Hi
Can somebody help me know , How can i mount a USB drive in my AIX 5.3 ML6, P570 Server. This is a Bit urgent for me. Thanks in advance..
Regards
Raj (0 Replies)
Discussion started by: rdkumarj
0 Replies
10. UNIX for Advanced & Expert Users
Hi there,
Can anyone tell me the advantages that jfs has over Veritas (if any)??
Cheers. (5 Replies)
Discussion started by: rich
5 Replies
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)
NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO
usb(4)
STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD
March 18, 2014 BSD