Mapping is done at host level (on v7000), if he is missing one WWN, that affect should be global and NOT to a particular LUN.
@Murali969, the failed path is from Storage, can you cross verify on all other hdisks the path is up? is it showing Failed on the below for other hdisks too?
5005076802408847
If that's the case, then it could be that they just zoned three and missed out on (50050XXX).
Ask the storage team to look in to Fabric again.
Can you paste the output of fcstat fcs3 | grep -p "FC SCSI Traffic Statistics"
Also, send me the errpt -a for that failed path if it is logged.
Hmmm,
So, we know it's not the problem with your fcs3, and looking at the output of your lsdev -Ccdisk, I am assuming you don't have MPIO pcmpath installed on your system.
With v7000 storage, IBM MPIO- SDDPCM is free.
Can you paste the output of
Code:
lsattr -El hdisk10 -a "algorithm hcheck_interval reserve_policy"
lsattr -El fscsi3 -a "dyntrk fc_err_recov"
Do this ONLY, if the disk is free:
Is the disk in use? lspv | grep hdisk10, if its not in use try to delete the disk and re-configure.
Hello,
I have encountered the issue on my AIX 6.1. As you can see below, the hdisk1 & hdisk8 are not recognized by the system
/ > lspv
hdisk0 00fa6d1288c820aa rootvg active
hdisk1 00fa6d1288c8213c None
hdisk2 ... (9 Replies)
Hello,
I have some concerns over the disk management of my AIX system.
For example server1
/ > lspv
hdisk0 00fa6d1288c820aa rootvg active
hdisk1 00fa6d1288c8213c vg_2 active
hdisk2 00c1cc14d6de272b ... (6 Replies)
This is getting very confusing for me, and appreciate if someone can help.
Platform: Power VM ( Virtual I/O Server)
ioslevel 2.1.3.10-FP23
# oslevel -s
6100-05-00-0000
Storage: IBM DS4300
Two HBAs - Dual Port Fibre Adapter Channels
Each card has two ports , so a total of 4 ports going... (3 Replies)
Hello,
we are planning to deploy some of our databases on AIX/LPAR based servers (we didn't bought it yet ...). IBM's engineers says that if we want to boot them from SAN the hardware array has to be compatible with MPIO but they don't want to deliver any document with list of arrays supported... (5 Replies)
Hi,
we have a vew boxes using MPIO and they are connected to some virtualization software managing some disk subsystems, offering volumes to the AIX boxes.
Sometimes when a cable has been plugged out for a test or when a real problem occurs, using lspath to show the state of the paths shows... (8 Replies)
On a particular LPAR, I was running AIX 5.3 TL 3. On Monday I did an update of the LPAR to 5.3 TL 9 SP2. The install was smooth, but then I ran into a problem.
The MPIO driver does not work with LSI's StoreAge (SVM4). I did some looking, and looks like
5.3 TL3 = IBM.MPIO 5.3.0.30
5.3... (0 Replies)
Hello All,
After creating lpp_source/spot from AIX 5.3TL6-07 DVD on the NIM(AIX6.1), I went online and download the fix pack for reaching TL8-04. (it was less than 200Mgegs total)
then I did define a newer lpp_source530TL8-04 via a copy from the older lpp_source530TL6-07 (I diduse a command... (2 Replies)
Hi folks,
does anybody have a link to a documentation how to implement native MPIO on AIX? We are using EMC PowerPath and Datacore SanSymphony/Cambex for this so far and I wasn't able to find a good description on that topic. All I know so far is that mkpath, chpath and lspath are used to... (3 Replies)
Hi All,
The path requires me to go Single User mode. On single user mode, the patch still won't continue:
dhcpagent supports a new keyword in /etc/default/dhcpagent.
Please merge the existing /etc/default/dhcpagent with the
patched version of /etc/default/dhcpagent shipped with this... (2 Replies)
We are looking at running MPIO for it's redundancy and load balancing benefits. Does anyone know what pieces of software or modules are needed on the VIO server to get load balancing to work. Remember we are using EMC's DMX3500 storage system. We no longer want to use Powerpath. :rolleyes: ... (2 Replies)
11-20-2013
