Hi all,
I am not sure whether anyone of you using XIV to copy vg from one host to another. After I managed to copy all the respective vg over to destination vg, and map all vg to destination and when come to varyonvg, I got the following error
0516-510 varyonvg: Physical volume not found for physical volume
identifier 00f626989f51fcae.
Anyone encounter this before, hope you can share some idea why it happen and how to resolve this ?
Is this something I didn't perform before I varyonvg ?
before to try the varyonvg, could you check if lspv shows the same content in both nodes
I not have experience in XIV, but in another Storage Copies (EMC, HDS), probably you need clean the reservations that the original system put in the physical devices.
I think tyhat you need heck that the attributes on same nodes are the same, use lsattr -El hdiskX to review these, in special the reservation policy values.
Location: on the road for work; home is private time
Posts: 456
Thanks Given: 10
Thanked 108 Times in 100 Posts
This does not have anything to do with the storage system used.
By copy, did you use a command like dd to make the copy? Or did you have LUNS active from both systems and use something like migratepv commands? If so, I am guessing that you removed the old LUN before doing a reducevg command.
Does lspv show a disk as PVMISSING?
If you are facing a PVMISSING disk you could look at my post from 2007 on HOWTO: Cleanup a PVMISSING disk
In any case, (i.e., even if you are not seeing a PVMISSING message) your message reads as if there is a PVID in the VGDA that needs to be removed before you can varyonvg the volume group. More details in the article above - however, here are the basics:
Code:
root@aix53:[/]lsvg -p vgExport
0516-010 : Volume group must be varied on; use varyonvg command.
root@aix53:[/]varyonvg vgExport
PV Status: hdisk1 00c39b8d69c45344 PVACTIVE
hdisk2 00c39b8d043427b6 PVMISSING
Get a list of all the logical volumes on the missing disk
Code:
root@aix53:[/]lspv -l -v 00c39b8d00004c000000011169c45a4b hdisk2
hdisk2:
LV NAME LPs PPs DISTRIBUTION MOUNT POINT
lvTest 512 512 109..108..108..108..79 /scratch
loglv00 1 1 00..00..00..00..01 N/A
If the last command does not list any logical volumes you can proceed to removing the disk from the volume group (i.e., remove from the VGDA) - otherwise you will need to remove the logical volumes from the volume group before removing the disk.
Code:
root@aix53:[/]ldeletepv -g 00c39b8d00004c000000011169c45a4b -p 00c39b8d043427b6Note: there is no output for the above command when all proceeds accordingly.
Hi there,
I am trying to determine if a specific XIV LUN on AIX is in OPEN or CLOSED state. I would like tthe same info as I can get from pcmpath command on v7000 LUN-s. I would need this info to find out if I can safely delete a LUN or not.
I tried fuser command, but no luck. It did not... (6 Replies)
Iam new to AIX
I am unable varyonvg on the vios,some of the disk are reported as harware failure.
I am going to replace the disk,Please tell me how to remove the disk without any corruption in the VG
lspv -l hdiskx also didn't work (0 Replies)
I am trying to move content of a folder usingls /backup/db_backups/INCREMENTAL/|while read file ; do
mv $file /backup_LOCAL/db_backups/INCREMENTAL/
done...but when I run this command using a bash script I'm getting this error ./test.sh
mv: cannot stat... (6 Replies)
Hi guys,
I had a solaris box, with veritas controled disk.
1 disc is showing soft errors, how can I repair the soft errors?
Please help.
Cheers; (4 Replies)
Hi,
I'm learning for my Solaris 10 sys-admin part 2. I'm now trying to get nis working because for the exercise. I run in to a problem.
Setup:
Three Systems
solaris101 (client)
Nothing wrong here havent made any config changes yet.
solaris102 (master server)
Interfaces
... (1 Reply)
Hello,
On Aix 5.3, during importvg, the varyonvg fails:
importvg -y vgtest hdisk20
0516-013 varyonvg: The volume group cannot be varied on because
there are no good copies of the descriptor area.
When i use manually the command varyonvg -u -b -t vgtest to force, the vg can... (3 Replies)
Hi all.
I'm new to AIX, so... We are running a BCV process between two AIX 5 machines attached to EMC Clariion SAN. During the varyonvg portion of the BCV process, we experienced a failure due to the physical volume is marked missing (PVMISSING). What diagnostics can I run to see the missing... (2 Replies)
Good evening,
Thanks a lot for your help, we appreciate it a bunch. Heres basically a summary of what we have (sorry Im adding some extra history as well):
We have 2 Ibm Servers (Hag and Aki) that are running AIX Version 5. Each connect to a SAN device via 2 separate fiber paths. Hag seems to... (9 Replies)
I am trying to move a file that is in the root directory. I suspect it is an old file created by someone when the system was installed. I am testing accessing the file by doing a copy but the command does not find the file.
I am operating as root. We are HP-UX B.11.23
I do long listing and... (3 Replies)
Hello all,
Strange problem on p5 520 server. I've created two volume groups, filesystems, etc.. Everything working fine, without any problem. After some tests with a DS4300 unit I wanted to remove the volume groups, change the DS4300 configuration, and re-create a new volumegroup. However, I'm... (0 Replies)