p520 Service Processor's IP

10 More Discussions You Might Find Interesting

1. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

2. AIX

running LPAR on power5 p520 hardware

picked up an old p520..and also spend sometimes to manage software: a) AIX 7.1 b) VIOS Server 2.2 attempting to run a few LPARs without much more $$$$, as this is a home-made projects.. machine hdisk0, pre-installed with AIX 7.1 a few questions: a) In order to run LPARs, I will...

3. AIX

VIO server on p520

trying to put VIO server software into this p520, firmware upgraded to the latest and greatest..SF240_415_318 , I think a few questions, on this practice AIX machine on AIX 7.1 VIO can only be installed if ASMI or HMC is running ??? if so, perhaps ASMI is much simpler, since I will need to...

4. AIX

p520 -- amber light

it shows up after the upgrade to SF240_415, after 2 hrs. amber light shows up on the led of 9111-520, but alog shows: everything seems to work, not sure what's going on..

5. AIX

P520 AIX com port (tty0) settings

I have software running under AIX 5.3 that should communicate with a special device using standard communication protocol (Modbus) using serial RS-232 line The settings are correct in both sides, But I can't establish a connection. I suspect that there's something that I should do regarding the...

6. AIX

Connecting to the service processor?

Hi Folks, I am a new AIX user. This is my first post in the UNIX forums. I did do a little bit of search before creating this post, but did not find any conclusive information. I am trying to connect to the service processor of an older 44p Model 170 box using my laptop. The 44p box has two...

7. AIX

LPAR processor/virtual processor settings

Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities. Environment is a 8-way p570 with 4 LPARs. lparVIO1 and lparVIO2: AIX 5300-04-01 Mode/Type= Shared-SMT/Capped Minimum Processors= 0.10 Desired Processors= 0.50 Maximum...

8. AIX

installing aix 5.2 on p520

hello everybody. Has anyone tried to install aix 5.2 on p520 machines. I've been trying but in the installation menu it says, "no disk found". I've used the same CD on a different 520 server and its working fine on it. Can anyone help, please?

9. AIX

connecting to service processor on 44P 170

I dont have an ascii terminal to hook upto this thing, trying to use my laptop but it doesnt seem to want to communicate, is there a special cable i should be using for this?

10. HP-UX

Service processor not responding

I am receiving messages from HP-UX Server "The operating system is unable to communicate with the service processor. The support bus which connects the system processors, the service processor and the Power Monitor or Platform Monitor may have become hung ". I need help in the following:...

LEARN ABOUT MINIX

term

TERM(1) 						      General Commands Manual							   TERM(1)

NAME

       term - turn PC into a dumb terminal [IBM]

SYNOPSIS

       term [baudrate] [parity] [bits_per_character] [-dial_string] [device]

EXAMPLES

       term 2400	   # Talk to modem at 2400 baud

       term 1200 7 even    # 1200 baud, 7 bits/char, even parity

       term 8 9600 /dev/tty01
			   # 9600 baud, 8 bits/char, no parity, use tty01

       term -atdt12345 /dev/tty01
			   # Start with a command to dial out

DESCRIPTION

       Term  allows MINIX to talk to a terminal or modem over RS232 port 1.  The program first sets the baudrate, parity and character length, and
       then forks.  The parent sits in a loop copying from stdin (usually the console's keyboard), to the terminal  or	modem  (/dev/tty00).   The
       child  sits  in a loop copying from the terminal or modem (/dev/tty00) to standard output.  Thus when RS232 port 1 is connected to a modem,
       every keystroke typed on the keyboard is sent to the modem, and every character arriving from the modem is displayed.  Standard	input  and
       output  may  be redirected, to provide a primitive file transfer program, with no checking.  Any argument that starts with a minus ('-') is
       sent out to the modem, usually to dial out.  Term accepts several commands that are formed by typing the escape character,  CTRL-],  and  a
       letter.	 Type  CTRL-]?	to  see  a list of commands.  The subshell command is very important, it allows you to type in a ZMODEM command to
       transfer data.  Do not quit term to do this, or your modem line will be reset!  Term keeps the modem line open on file descriptor  9  while
       running the subshell, so you can type

	    <&9 >&9

       at the end of your ZMODEM command to connect it to the modem.

       Important  note: to use term, it is essential that /etc/ttytab is configured so that there is no shell hanging on /dev/tty01.  If there is,
       both the shell and term will try to read from /dev/tty01, and nothing will work.

SEE ALSO

       rz(1), sz(1).

																	   TERM(1)

AIX