10 More Discussions You Might Find Interesting
1. AIX
Hello,
I found that the packet counts given by entstat -d SEA is not the same as the total of the packet counts given by seastat -d SEA for the same interval of time.
Do anyone have an explanation for the difference. We recently got a recommendation that the throughput on an SEA should not... (5 Replies)
Discussion started by: N8R
5 Replies
2. AIX
hello,
what will happen if i try to move sea of my 1 vio server to standby( using chdev command), when sea of other vio server is already in standby mode? (1 Reply)
Discussion started by: amvineeth
1 Replies
3. AIX
i want configure a SEA over my vios ,
i have a message error :
Method error (/usr/lib/methods/cfgsea):
Failed to configure SEA with return code 1 and SEA-specific error code 10:
Detailed info: Setting real adapter ent1 in promiscuous mode failed... (5 Replies)
Discussion started by: hedou
5 Replies
4. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
5. AIX
I am trying to install a VIOS pair with a load-sharing SEA adapter, following this recipe from Developerworks. Without load-sharing everything went fine and worked as expected, but somehow i am a bit lost and the first tries with "ha_mode=sharing" didn't work at all.
Here is the situation:
I... (6 Replies)
Discussion started by: bakunin
6 Replies
6. Linux
Hi,
Can we set password for linux in non-interactive mode.
I didn't find suitable option for this in man page.
If we wnter "passwd" command, it will tell "Enter password" and "Re-enter password". i wanted to run this step in a script, and i don't want to use "expect" so i am looking for a single... (8 Replies)
Discussion started by: successlin
8 Replies
7. AIX
Hi all,
I set up the following configuration on my system:
- An LPar with a virtual adapter, first one with a vlan id=703 and id port=13.
- The first adapter have to connect to a VIOS in which i configured an SEA.
So, the VA is set up on interface ent2, SEA on ent29 (by linking a... (0 Replies)
Discussion started by: idro
0 Replies
8. AIX
Hi Guys,
I'm getting the below error while trying to create a SEA adapter in VIOS
$ mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 1
... (4 Replies)
Discussion started by: kkeng808
4 Replies
9. AIX
I am trying to create a SEA on a LHEA port and it gives me error
lsdev -Cc adapter:
ent0 logical host ethernet port (l-hea)
ent1 virtual I/O ethernet adapter
mkvdev -sea ent0 -vadapter ent1 -default ent1 -defaultid 199
method error (/usr/lib/methods/cfgsea):
Failed to configure SEA... (0 Replies)
Discussion started by: filosophizer
0 Replies
10. Shell Programming and Scripting
Okay, not sure if it can be done, I would think it could be done and I'm just having a hard time with it.
fun_close_wait(){
ipVar="${1} ${2}"
portVar=`cat "${5}" | cut -d' ' -f 1`
for ip in $ipVar
do
for port in $portVar
do
netstatVar=`netstat -n | grep... (4 Replies)
Discussion started by: cbo0485
4 Replies
11-16-2011
