10 More Discussions You Might Find Interesting
1. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
2. Solaris
In a Solaris9 environment I'm trying to restore flash archive (flar) with SVM mirrored devices to same server via jumpstart server and it is failing to create boot file and drops down to a command prompt in single user mode, metastat -i and metastat -p output looks good when compared to the ones... (0 Replies)
Discussion started by: mbak
0 Replies
3. UNIX for Advanced & Expert Users
Hi,
I want to have one binary image that contains both my boot loader as well as the OS(linux) image at pre defined offsets which i can use to program flash . Can anyone help in this direction?
Regards
Subrata (0 Replies)
Discussion started by: subratasaharia
0 Replies
4. AIX
Hi,
I want to know wheather partition size for installation of vio client can be specified on vio server
example
If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Discussion started by: manoj.solaris
1 Replies
5. Filesystems, Disks and Memory
Hello All,
I backed up my RHEL 4 as an image.
Then I restored the image on my machine. Everything went fine but I dont get the normal boot sequence as it used to come when I freshly installed RHEL4.
The messages that are shown when the system boots are something like-
" .....
EXT3-fs:... (2 Replies)
Discussion started by: shamik
2 Replies
6. Red Hat
I'm running redhat linux: 2.6.18-128.1.6.el5xen #1 SMP Tue Mar 24 12:28:27 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux as my Dom0.
I have several other DomU's running on this system, but for this test I've shut them down.
I'm attempting to boot winXP from an image.
Here is my config file:
#... (3 Replies)
Discussion started by: willjw1
3 Replies
7. AIX
hi all
i just found one of my p650 server showing a warning message when i
tried to run bosboot command after upgrading TL to AIX 530803.
i also tried to run chpv -c hdisk0 and chpv -c hdisk1 to clear out the
old boot info in hdisk0 and hdisk1 and rerun bosboot -a. it still
showed... (0 Replies)
Discussion started by: rs6000er
0 Replies
8. AIX
My mksysb scripts gives the following text on standard error:
bosboot: Boot image is 22995 512 byte blocks.
How come on a Aix 5200-07 aix-system.
I thought this message meant that the tape (/dev/rmt0) is not bootable,
but I read about a limit of 12 MB and 22995 block is less than 12 MB
... (0 Replies)
Discussion started by: frankwiel
0 Replies
9. AIX
hello
i saved my system this morning, mksysb tape, and i have the message: "boot.image exceeded the size....." i have not the end because the message is disappeared.
where can i find the mksysb message in a log ?
the message is scary ?
thank you (6 Replies)
Discussion started by: pascalbout
6 Replies
10. Filesystems, Disks and Memory
Where can I find the boot floppy disk image file(*.vfd)of SCO UNIX 5.0.5?:confused: (1 Reply)
Discussion started by: whiteknight
1 Replies