10 More Discussions You Might Find Interesting
1. AIX
Friend's,
I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client?
All leads to the answer would be much appreciated, many thanks!
-- Souvik (2 Replies)
Discussion started by: thisissouvik
2 Replies
2. AIX
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies
3. AIX
Hi Guys,
I'm building a new NIM environment with clients on 3 different subnets. I want to get some advise on what is the best approach for this kind of setup.
This is the sample network for my new NIM.
Master IP: 10.20.1.20
Client IP subnet_1: 10.20.1.21
Client IP subnet_1: 10.30.1.21... (5 Replies)
Discussion started by: kaelu26
5 Replies
4. AIX
Hi.
I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ?
Tks (2 Replies)
Discussion started by: stephnane
2 Replies
5. UNIX for Advanced & Expert Users
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies
6. AIX
I am new to this forum so please bare with me. I did search for this answer prior to posting but no luck.
Running an AIX NIM Master at 5.3TL9SP4, with about 100 clients. The subnet of one of the networks defined in the NIM env has changed. When I go to Manage Networks, Change/Show... (0 Replies)
Discussion started by: juredd1
0 Replies
7. AIX
Hello everyone
Im trying to backup a nim client from nim master but I got this message
COMMAND STATUS
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
0042-001 nim:... (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
8. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
9. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
10. AIX
I try to migrate a NIM server from one server to another.
I try to do a mksysb on NIM server
restore the NIM server's mksysb to a client through NIM installation
shutdown NIM server
start newly installed client as NIM server
Does anyone do this before? who can give me some suggestion? (1 Reply)
Discussion started by: yanzhang
1 Replies
ris(8) System Manager's Manual ris(8)
Name
ris - remote installation services utility
Syntax
/etc/ris
Description
The utility performs remote installation services which install system software to a client machine through the TCP/IP local network. The
client machine can be a VAX or a RISC machine.
The server on which the remote installation services area is located can be either a VAX or a RISC machine.
The remote installation services utility uses the directory as a base. When you install the first product to the utility creates a remote
installation services area. The area is called either or
The area contains one or more ULTRIX software products. Each product contains the subsets of the kits that can be installed to clients on
a network. Clients registered for an area install software over the network to their processor.
The utility performs the following functions:
a - Add client
r - Remove client
s - Show products in remote installation environments
m - Modify client
i - Install software
You must use the utility interactively to set up a remote installation services area. After you have set up a remote installation services
area on the server, you can use the utility either interactively or from the command line to manage clients.
The directory also holds a subdirectory, This directory contains a database file, that you can use to manage multiple clients.
Examples
The example that follows invokes the utility interactively:
# /etc/ris
A menu appears from which you can select options to perform functions.
The examples that follow manage the client using the command line.
The syntax of the command to add a client follows:
/etc/ris -a <clientname> -h <Ethernet_address> -p path,product[,product]
The following command adds client and allows that client to install a product over the network:
# /etc/ris -a bergal -h 08-00-2B-03-05-8B -p ris0.mips,product_1
The syntax of the command to modify a client follows:
/etc/ris -a <clientname> [-h <Ethernet_address>] [-p <path,product,product>]
The following command modifies client and allows that client to install a product over the network:
# /etc/ris -m bergal -p ris0.mips,product_2
The syntax of the command to remove a client follows:
/etc/ris -r <clientname>
The following command removes client
# /etc/ris -r bergal
Files
See Also
setld(8)
Guide to the Remote Installation Services
Guide to Server Setup
ris(8)