Code:
# net.slp.maxResults
# A 32 bit integer giving the maximum number of results to accumulate and return for a
# synchronous request before the timeout, Positive integers and -1 are legal values.
# If -1, indicates that all results should be returned.
# Default value is -1.
# for example:
# net.slp.maxResults = 35
# net.slp.useScopes
# A value-list of strings indicating the only scopes a UA or SA is allowed to use when
# making requests or registering, or the scopes a DA must support.
# Default: scope "DEFAULT" is used if no other information is available.
# for example:
# net.slp.useScopes = david,bob
# net.slp.DAAddresses
# A value-list of IP addresses or DNS resolvable host names giving the SLPv2 DAs to use for
# statically configured UAs and SAs.
# Default is none.
# for example:
# net.slp.DAAddresses = 9.3.149.20, blahblah.ibm.com
# net.slp.isBroadcastOnly
# A boolean indicating if broadcast should be used instead of multicast.
# Default is false. So the default is multicast.
# for example:
# net.slp.isBroadcastOnly = false
# net.slp.multicastTTL
# A positive integer less than or equal to 255, giving the multicast TTL.
# Default is 255 (in seconds).
# for example:
# net.slp.multicastTTL = 255
# net.slp.DAActiveDiscoveryInterval
# A 16 bit positive integer giving the number of seconds between DA active discovery queries.
# If this parameter is set to zero, active discovery is turned off. This property corresponds
# to the protocol specification parameter CONFIG_DA_FIND.
# Default is 900 (in seconds).
# for example:
# net.slp.DAActiveDiscoveryInterval = 1200
# net.slp.multicastMaximumWait
# A 32 bit integer giving the maximum amount of time to perform multicast, in milliseconds.
# This property corresponds to the CONFIG_MC_MAX parameter in the protocol specification.
# Default is 15000 (in ms)
# for example:
# net.slp.multicastMaximumWait = 10000
# net.slp.multicastTimeouts
# A value-list of 32 bit integers used as timeouts, in milliseconds, to implement the multicast
# convergence algorithm. Each value specifies the time to wait before sending the next request.
# This property corresponds to the CONFIG_MC_RETRY parameter in the protocol specification.
# Default is: 3000,3000,3000,3000,3000 (in ms)
# There is no limitation on the maximum number entries to be specified. However the total sum
# of the entries can't be bigger than CONFIG_MC_RETRY (15000 in ms).
# for example:
# net.slp.multicastTimeouts = 2000, 3000, 4000
# net.slp.DADiscoveryTimeouts
# A value-list of 32 bit integers used as timeouts, in milliseconds, to implement the multicast
# convergence algorithm during active DA discovery. Each value specifies the time to wait
# before sending the next request,This property corresponds to the protocol specification
# parameter CONFIG_RETRY.
# Default is: 2000,2000,2000,2000,3000,4000 (in ms)
# There is no limitation on the maximum number entries to be specified. However the total sum
# of the entries can't be bigger than CONFIG_RETRY (15000 in ms).
# for example:
# net.slp.DADiscoveryTimeouts = 2000, 3000, 4000
# net.slp.datagramTimeouts
# A value-list of 32 bit integers used as timeouts, in milliseconds, to implement unicast
# datagram transmission to DAs. The nth value gives the time to block waiting for a reply on
# the nth try to contact the DA. The sum of these values is the protocol specification
# property CONFIG_RETRY_MAX.
# Default is: 2000, 2000, 2000, 2000, 3000, 4000 (in ms)
# There is no limitation on the maximum number entries to be specified. However the total sum
# of the entries can't be bigger than CONFIG_RETRY_MAX (15000 in ms).
# for example:
# net.slp.datagramTimeouts = 2000, 3000, 4000
# net.slp.SAAttributes
# A comma-separated list of parenthesized attribute/value list pairs that the SA must advertise
# in SAAdverts. The property must be in the SLP attribute list wire format, including escapes
# for reserved characters.
# for example:
# net.slp.SAAttributes = (user=zaphod,trillian,roger,marvin)
# net.slp.interfaces
# Value-list of strings giving the IP addresses of network interfaces on which the DA or SA
# should listen on port 427 for multicast, unicast UDP, and TCP messages. Default is empty,
# i.e. use the default network interface.
# for example:
# net.slp.interfaces = 9.3.149.20,9.3.149.50