9 More Discussions You Might Find Interesting
1. Red Hat
Hi all,
actually i'm facing this problem,
we have 2 NICs on our VM.s with REDHAT 7.2 release,
we made the following set up as we needed to access them from both IP
ip route flush all
ip route add 10.130.11.0/24 dev eno2 tab 1
ip route add 10.130.10.0/24 dev eno1 tab 2
ip route add... (0 Replies)
Discussion started by: charli1
0 Replies
2. Solaris
Hi All
Recently we have faced issue in SUN server
after reboot of node 2 default routs has been added to system as below
IRE Table: IPv4
**Destination*************Mask***********Gateway**********Device Mxfrg Rtt***Ref Flg**Out**In/Fwd*
-------------------- ---------------... (2 Replies)
Discussion started by: aaysa123
2 Replies
3. Solaris
After running a script for Platform Patch, the default route is removed from netstat -nrv.
The machine does not reboot after Platform Patch.
The script does not have any command to remove default route as shown below...
route del default gw <IP>
I am wondering, how is the defaut route... (10 Replies)
Discussion started by: frintocf
10 Replies
4. AIX
AIX version 5.3
when I try to add default gateway
# route add 0 192.168.100.254
Or
# route add default 192.168.100.254
I get the error
0821-275 route: socket: The file access permissions do not allow the specified action.
searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies
5. IP Networking
Greetings,
I am using debian squeeze to perform the following operation:
1. pxeboot Alix 2.c board into debian installer
When I get to the installer my laptop's dhcp server successfully provides an ip address but does not set up the default route. I am not sure how to provide this.
I... (2 Replies)
Discussion started by: mock
2 Replies
6. Solaris
Hiya,
I got the default gateway set in /etc/defaultrouter file, however "netstat -nr" doesn't show anything like "default" in the routing table. As far as I know "netstat" on Solaris 10 u7 should show something like :
Routing Table: IPv4
Destination Gateway Flags Ref ... (8 Replies)
Discussion started by: TomSu
8 Replies
7. AIX
Hello I have a question regarding default route on AIX servers. (I am using a p5 5.3 TL9 machine).
in my output of "lsattr -El inet0" I can see there are two routes like below.
route net,-hopcount,0,,0,x.x.207.7 Route True
route net,-hopcount,0,,0,x.x.202.129 Route True
But... (9 Replies)
Discussion started by: gsabarinath
9 Replies
8. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
9. AIX
Hi,
We are running AIX 5.2.
Our default gateway used to be IP Address A.
Our new default gateway is IP Address B.
A netstat revealed that our default route was IP address A.
We manually added default route with IP address B and removed the default route with IP address A.
However,... (3 Replies)
Discussion started by: DenD
3 Replies
condor_router_q(1) General Commands Manual condor_router_q(1)
Name
condor_router_q Display - information about routed jobs in the queue
Synopsis
condor_router_q [-S] [-R] [-I] [-H] [-route name] [-idle] [-held] [-constraint X] [condor_q options]
Description
condor_router_q displays information about jobs managed by the condor_job_routerthat are in the Condor job queue. The functionality of this
tool is that of condor_q, with additional options specialized for routed jobs. Therefore, any of the options for condor_qmay also be used
with condor_router_q .
Options
-S
Summarize the state of the jobs on each route.
-R
Summarize the running jobs on each route.
-I
Summarize the idle jobs on each route.
-H
Summarize the held jobs on each route.
-route name
Display only the jobs on the route identified by name.
-idle
Display only the idle jobs.
-held
Display only the held jobs.
-constraint X
Display only the jobs matching constraint X.
Exit Status
condor_router_q will exit with a status of 0 (zero) upon success, and non-zero otherwise.
Author
Condor Team, University of Wisconsin-Madison
Copyright
Copyright (C) 1990-2012 Condor Team, Computer Sciences Department, University of Wisconsin-Madison, Madison, WI. All Rights Reserved.
Licensed under the Apache License, Version 2.0.
See the Condor Version 7.8.2 Manualor http://www.condorproject.org/licensefor additional notices. condor-admin@cs.wisc.edu
September 2012 condor_router_q(1)