01-31-2006
I don't know what you're doing - but getrusage() is the standard way to get cpu usage - usually in ms.
10 More Discussions You Might Find Interesting
1. Programming
how can i monitor usages of CPU, Memory, Hard disk etc. under SUN Solaries
through a c program or java program
i want to store that data into database so i can show it graphically
thanks in advance (2 Replies)
Discussion started by: Gajanad Bihani
2 Replies
2. HP-UX
how can I find cpu usage memory usage swap usage and
I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times
my final destination is monitor process
logical volume usage above X % and number of Logical voluage above
can I not to... (3 Replies)
Discussion started by: alert0919
3 Replies
3. Solaris
Hi,
I want to monitor the current cpu usage, monitor usage , disk I/o and network utlization for solaris using SNMP.
I want the oids for above tasks.
can you please tell me that
Thank you (2 Replies)
Discussion started by: S_venkatesh
2 Replies
4. AIX
How to monitor the IBM AIX server for I/O usage, memory usage, CPU usage, network usage, storage usage? (3 Replies)
Discussion started by: laknar
3 Replies
5. UNIX for Dummies Questions & Answers
Hi all,
Can you please tell me the command, with which one can know the amount of space a specific directory has used.
df -k . ---> Displays, the amount of space allocated, and used for a directory.
du -k <dir name> - gives me the memory used of all the files inside <dir>
But i... (2 Replies)
Discussion started by: abhisheksunkari
2 Replies
6. Linux
hello,
I have purchased VPS from one webhosting company. VPS comes with Virtuozzo power panel. It has 512MB gurranted RAM and dynamic RAM 2048 MB.
I have hosted single domain with 50MB database and wordpress installation.
But I am getting resource alerts. It goes sometime in yellow... (8 Replies)
Discussion started by: mrugesh78
8 Replies
7. AIX
Hello Everyone,
I'm looking for a efficient script that monitors the memory usage on AIX and send email alerts when it reaches certain point.
Q) need to get alerts, when the memory usage exceed 90% on AIX?
or
Q) Need to get alerts when available free Memory is 1G or 10% etc
Any idea... (3 Replies)
Discussion started by: System Admin 77
3 Replies
8. UNIX for Dummies Questions & Answers
Let's say i have 20 users logged on Server. How can I know how much memory percent used each of them is using with system time in each user? (2 Replies)
Discussion started by: roy1912
2 Replies
9. Solaris
Hello Friends,
I need to check memory usage & availability before I could run a program if there is enough memory is left or not, so how could i achieve this? Which command output i should rely on? I have diplayed outputs of SAR, VMstat and PRstat commands below, But how could i check memory... (8 Replies)
Discussion started by: EAGL€
8 Replies
10. UNIX for Beginners Questions & Answers
I can't check actual memory usage in the Redhat 5.5...
The used memory is 14214 Mb of Total 15919 by Free -m command.
I sum the RSS value on PS aux command result and the value is 5428.66Mb.
Yes It's quite different actual usage memory and RSS value.
So I added Shared memory value... (5 Replies)
Discussion started by: tom8254
5 Replies
ln(4) Kernel Interfaces Manual ln(4)
Name
ln - Lance Ethernet interface
Syntax
device ln0 at ibus? vector lnintr
Description
The interface provides access to a 10 Mb/s Ethernet network through the Lance controller.
The host's Internet address is specified at boot time with an SIOCSIFADDR ioctl. The interface employs the address resolution protocol
described in to map dynamically between Internet and Ethernet addresses on the local network.
The interface normally tries to use a trailer encapsulation to minimize copying data on input and output. This can be disabled for an
interface by setting the IFF_NOTRAILERS flag with an SIOCSIFFLAGS ioctl. Trailers are only used for packets destined for Internet hosts.
The SIOCSPHYSADDR ioctl can be used to change the physical address of the Lance. The SIOCRPHYSADDR ioctl can be used to read the physical
address of the Lance.
The SIOCADDMULTI and SIOCDELMULTI ioctls can be used to add or delete multicast addresses. The Lance recognizes a maximum of 12 multicast
addresses.
The SIOCRDCTRS and SIOCRDZCTRS ioctls can be used to read or ``read and clear'' the Ethernet driver counters. The argument to these two
ioctls is a pointer to a counter structure, found in
The SIOCENABLBACK and SIOCDISABLBACK ioctls can be used to enable and disable the interface loopback mode respectively.
Diagnostics
The diagnostic error messages contain relevant information provided by the Lance.
ln%d: can't handle af%d
The interface was handed a message with addresses formated in an unsuitable address family, and the packet was dropped.
ln%d: memory error (MERR)
A memory parity error has occurred.
ln%d: lnalloc: cannot alloc memory ...
The driver was unable to allocate memory for internal data structures.
ln%d: initialization error
The driver was unable to initialize the network interface.
ln%d: SIOCADDMULTI fail, multicast list full
Too many multicast requests have been made.
See Also
arp(4p), inet(4f), intro(4n)
ln(4)