01-06-2006
Normally, swapfiles are allocated in the "middle" of the disk and are created so that they are pretty much contiguous.
The reason is so that the disk head, on average, will have to move the shortest distance before it hits the cylinder in the swapfile it needs.
Having the file at the beginning or end of the disk is not a big deal but it will, on average, increase seek time.
See:
http://en.wikipedia.org/wiki/Seek_time
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
When i re-updated my system i set my swap at 500 MB. I have 256 in ram and have never even gone into the 250 mb of swap that i had originally configured. How do I reduce the swap? (3 Replies)
Discussion started by: macdonto
3 Replies
2. Solaris
So with solaris 10 are people not using the old /tmp as a regular UFS filesystem and making /tmp part of swap or tmpfs... what are peoples thoughts on this? (5 Replies)
Discussion started by: csaunders
5 Replies
3. Solaris
When i try to type swap -l ,nothing come out but blinking.
May i know what is the problem and solutions ?
thanks (6 Replies)
Discussion started by: Farbegas
6 Replies
4. Solaris
Hello and thanks in advance.
I have a Sun box with raid 1 on the O/S disks using solaris svm.
I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space.
I have been warned not to do this by some... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies
5. HP-UX
I have a HP-UX B.11.23 server with 16 gb of memory 84 gb of swap configured. I am being pushed to define more swap to try and get more Tuxedo domains to start. At what point do we have too much swap for the amount of memory? Thanks in advance. (11 Replies)
Discussion started by: scotbuff
11 Replies
6. Red Hat
free -m : 1023 total swap space
created default partition /dev/sdb1 50M using fdisk. i did write the changes.
#mkswap /dev/sdb1
#swapon /dev/sdb1
free -m : 1078 total swap space
this shows that the swap is on
Question : i did not change the type LINUX SWAP (82) in fdisk.
so why is... (5 Replies)
Discussion started by: dplinux
5 Replies
7. HP-UX
Hi
I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system:
- I would like to know when does the memory swap space spill over to the device swap space?
- And how much % of memory swap utilization should be specified (swap space device... (6 Replies)
Discussion started by: lamoul
6 Replies
8. Red Hat
Hi,
I have added a new disk to production server. How to make it visible to os and how to configure it. I also want to add some space from that disk to swap space. Please help me out. (1 Reply)
Discussion started by: chetansingh23
1 Replies
9. Solaris
Hi,
Can somebody please help here, since iam just a beginner.
According to my book knowledge.
the Avalilable memory calculated by swap -l (includes only swap) should be small as compared to swap -s value(includes Virtual memory=swap +physical).
but this is quite opposite in my case.
swap... (6 Replies)
Discussion started by: Laxxi
6 Replies
10. Solaris
Hi Solaris Folks :),
I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands.
$swap -s
total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available
$swap -l
swapfile dev swaplo... (6 Replies)
Discussion started by: seenuvasan1985
6 Replies
LEARN ABOUT DEBIAN
tunefs
tunefs(1M) System Administration Commands tunefs(1M)
NAME
tunefs - tune an existing UFS file system
SYNOPSIS
tunefs [-a maxcontig] [-d rotdelay] [-e maxbpg] [-m minfree] [-o space | time] special | filesystem
DESCRIPTION
tunefs is designed to change the dynamic parameters of a file system that affect the layout policies. When using tunefs with filesystem,
filesystem must be in /etc/vfstab. The parameters that can be changed are indicated by the options given below.
OPTIONS
The following options are supported:
-a maxcontig
The maximum number of logical blocks, belonging to one file, that is allocated contiguously. The default is calculated as follows:
maxcontig = disk drive maximum transfer size / disk block size
If the disk drive's maximum transfer size cannot be determined, the default value for maxcontig is calculated from kernel parameters as
follows:
If maxphys is less than ufs_maxmaxphys, which is 1 Mbyte, then maxcontig is set to maxphys. Otherwise, maxcontig is set to ufs_maxmax-
phys.
You can set maxcontig to any positive integer value.
The actual value will be the lesser of what has been specified and what the hardware supports.
-d rotdelay
This parameter is obsolete as of the Solaris 10 release. The value is always set to 0, regardless of the input value.
-e maxbpg
Indicates the maximum number of contiguous logical blocks any single file can allocate from a cylinder group before it is forced to
begin allocating blocks from another cylinder group. Typically this value is set to approximately one quarter of the total contiguous
logical blocks in a cylinder group. The intent is to prevent any single file from using up all the blocks in a single cylinder group,
thus degrading access times for all files subsequently allocated in that cylinder group.
The effect of this limit is to cause big files to do long seeks more frequently than if they were allowed to allocate all the blocks in
a cylinder group before seeking elsewhere. For file systems with exclusively large files, this parameter should be set higher.
-m minfree
Specifies the minimum free space threshold, or the percentage of space held back from normal users. This value can be set to 0. How-
ever, up to a factor of three in throughput will be lost over the performance obtained at a 10% threshold. Note: If the value is raised
above the current usage level, users will be unable to allocate files until enough files have been deleted to get under the higher
threshold.
-o space|time
The file system can either be instructed to try to minimize the time spent allocating blocks, or to try to minimize the space fragmen-
tation on the disk. The default is time.
Generally, you should optimize for time unless the file system is over 90% full.
USAGE
See largefile(5) for the description of the behavior of tunefs when encountering files greater than or equal to 2 Gbyte ( 2**31 bytes).
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
mkfs_ufs(1M), newfs(1M), attributes(5), largefile(5)
SunOS 5.10 5 Dec 2003 tunefs(1M)