Sponsored Content
Top Forums UNIX for Dummies Questions & Answers boot fails after power faliure Post 94915 by Just Ice on Wednesday 4th of January 2006 06:57:30 PM
Old 01-04-2006
get the box to the ok prompt through stop-a and then type in "boot cdrom" ... make sure you reformat the drive when you reinstall ...

sun boxes can easily boot off the cdrom if there are no boot files found on the internal drives --- i'm guessing your process conked out after a bunch of the boot and system files have been put in so the system sees them and tries to boot off them after the reboot ... doing the stop-a and "boot cdrom" will insure that the box doesn't try to boot off the incomplete system installation ... good luck!
 

10 More Discussions You Might Find Interesting

1. AIX

AIX does not boot after power on

We have a RS6000, model B50, type 7046, where I installed AIX 4.3.3 But, if the power goes off, the operating system does not restart, and I have to go there and push the button to start AIX again. Is there any way this procedure to be avoided, this is, I want the AIX to start automatically... (9 Replies)
Discussion started by: sebastia.net
9 Replies

2. UNIX for Advanced & Expert Users

PXE diskless boot fails

Hi, I am trying to setup a server for a diskless boot of a computer class (with ubuntu) I followed the guidelines in https://help.ubuntu.com/community/DisklessUbuntuHowto I have two computers: one is the server I installed and the other is my macbook on which I run a virtual machine... (8 Replies)
Discussion started by: yotamhc
8 Replies

3. Solaris

T5220 fails to boot

One of our T5220 servers fail to boot due to following error: ERROR: The following devices are disabled: XAUI1 XAUI0 I can't see any disabled components in SP console, any idea what is the problem? (1 Reply)
Discussion started by: belalr
1 Replies

4. Solaris

Configure Power Settings on Boot

Hi all, this is my first question on this forum, so if it isn't in the correct location, please let me know where to post. We are using Solaris 8 and with the power setting enabled the monitor will not wake up. It can take anywhere from 5 to 30 minutes for the monitor to display. One of the... (3 Replies)
Discussion started by: Wrongway
3 Replies

5. Solaris

T2000 Sparc server fails boot

I have a T2000 enterprise SPARC server that's no longer on contract with Oracle. It's on old firmware (6.3.x). After a power-down this weekend, it won't boot normally. Boot snapshot at the bottom of the post. It can boot to cdrom, and it'll boot to failsafe mode, but it won't do a regular... (9 Replies)
Discussion started by: val riverwalk
9 Replies

6. AIX

System can't boot up after power outage

Hello Forum, I am very newbie with AIX. We have 2 AIX 9111-285 servers. The OS version is 5.3. After the power outage, they did not come up. I try to unplug the power cable and re-connect after 1 minutes but do not help. Both display the same reference code 110000AC on the front panel... (6 Replies)
Discussion started by: lilyn
6 Replies

7. AIX

Power RAID10 array reconstruct fails ?

Hello, P7 machine PCI Express x8 Planar 3Gb SAS Adapter RAID10 array(2 disks)(not AIX lvm) was configured and working, then one disk failed and IBM support replaced that. Now raid array is degraded, data is not lost. I see new disk model(same as original) serial and etc. What I did trying... (0 Replies)
Discussion started by: vilius
0 Replies

8. Solaris

M5000 fails to boot

I have an m5000 that Is down. I have access to XSCF> and was able to get to the ok prompt. However, on >ok boot it failed to boot. erred with : svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL. Nov 29... (3 Replies)
Discussion started by: goya
3 Replies

9. UNIX for Beginners Questions & Answers

Lucreate Fails to Create Boot Environment;

My OS solarius 5.10 Generic_147148-2 i86 Error: please review new boots environments using options 1. Solution - show me the commands Partition is full, try to remove some unneeded files, then try to compress some other unneeded files. man command creates a temp file under... (0 Replies)
Discussion started by: zbest1966
0 Replies

10. AIX

IBM Power 740 won't boot after firmware update

A team member installed the wrong version of License Code on a Power 740 system used in our Development environment. The system will no longer boot. Does anyone have IBM documentation or experience to share on recovering a system that currently reports "Unsupported License Code version... (1 Reply)
Discussion started by: kevinedailey
1 Replies
installboot(1M) 														   installboot(1M)

NAME
installboot - install bootblocks in a disk partition SYNOPSIS
installboot bootblk raw-disk-device The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition. The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be found using the -i option of uname(1). The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead. bootblk The name of the bootblock code. raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read- able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive. Example 1: Installing UFS Boot Block To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use: example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t0d0s0 /usr/platform/platform-name/lib/fs/ufs directory where ufs boot objects reside. /platform/platform-name/ufsboot second level program to boot from a disk or CD See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5) WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device. 11 Apr 2005 installboot(1M)
All times are GMT -4. The time now is 03:13 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy