12-27-2005
use command "print_manifest" to get the information about the system
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello, i have to activate a network interface. for HPUX1100 i can command ifconfig lanx plumb.
Why doesent it works under HPUX10.20?
How can i realise it?
thanks for your help!:) (2 Replies)
Discussion started by: ortsvorsteher
2 Replies
2. HP-UX
Hi guys,
Need a favour or information on how to get it done in configuring a HPUX-11i box?I need the commands which is needed to configure the box...The pdf's in HP site is too much to look at.Is there any advice from u guys on how could i settle this problem? (7 Replies)
Discussion started by: giriplug
7 Replies
3. AIX
Hi All,
Needed commands to find Monitor , chassis & keyboard related information on AIX.
Please please please help.
Thanks
VK (2 Replies)
Discussion started by: Veenak15
2 Replies
4. HP-UX
Hi All
Please somebody send me list of admin commands used for HPUX.
Thanks
Sunanda (2 Replies)
Discussion started by: sunanda
2 Replies
5. Solaris
Hi all
Got another strange one. If I try to enquire about the hardware, the command hangs implying Ive got a hardware issue. So, if I execute :-
iostat -en
sysdef - ( stops at the devices part )
format
cfgadm -al
Anything that searches the devices, then the command hangs.
... (4 Replies)
Discussion started by: sbk1972
4 Replies
6. HP-UX
I am new for HPUX OS and want to pursue my career in HPUX Administration.
I could not able to get following information from HP.com site, that why I need an assistance to know that - can I install HPUX 11i V3 OS on old HP B2000 & B1000 workstations (these workstation are 4 to 5 year old) or not,... (5 Replies)
Discussion started by: girish.batra
5 Replies
7. Solaris
Hi guru
I want to know which company's hardware is more stable means in term of H/W faults or replacement, in case of IBM (AIX), HP (HPUX) & SUN MICROSYSTEM (Solaris) & which order also, if we go through more stable to less stable system.
Regards (1 Reply)
Discussion started by: girish.batra
1 Replies
8. Hardware
Are there any other useful hardware commands to get information about your hardware? Is there any information that can't be found with these commands?
cat /proc/cpuinfo
cat /proc/meminfo
dmesg
lspci
sudo dmidecode
cpuid | more
lspci -v | grep VGA
sudo lspci -v -s 00:02.0
sudo lspci -vvv... (12 Replies)
Discussion started by: cokedude
12 Replies
9. HP-UX
We would like to know a HP Utility or any Unix command that can give the exact status of PCI Gigabit Ethernet cable (lan cable) We had tried to execute
lanscan
ioscan -fnC lan
The status appears to be the same when the cable is plugged & unplugged and also when the lan is disabled &... (5 Replies)
Discussion started by: siva3492
5 Replies
10. HP-UX
I own a 1999 vintage HP Logic Analyzer that runs HPUX 10.20. It is a 9000/775/rock system similar to a Visualize C132L/160L system.
I'm attempting, mostly for the fun of it, to upgrade the existing slow 5MB/s-only SCSI system, with a new-er PCI card. Of course drivers is my major concern. I'd... (2 Replies)
Discussion started by: KeithM
2 Replies
LEARN ABOUT OSF1
ip6_setup
ip6_setup(8) System Manager's Manual ip6_setup(8)
NAME
ip6_setup - IPv6 configuration program
SYNOPSIS
/usr/sbin/ip6_setup
DESCRIPTION
The ip6_setup utility allows you to configure the IPv6 networking software on your system.
To run ip6_setup, enter the following command and then answer the questions: # ip6_setup
You must know your Internet Protocol Version 6 (IPv6) address. If your network uses subnet routing, you must know the subnet mask for your
network. The network manager should be able to provide you with the information that you need.
After the ip6_setup command completes, the network services on the system can be restarted manually with the following command: #
/usr/sbin/rcinet restart
Before you restart the network services with the preceding command, warn the users that the network services on the system are being
removed. File systems that were not mounted using the /etc/fstab file or the automount command must be unmounted with the unmount command.
You must remount these file systems using the mount command after the network is started on your system.
Alternatively, you can reboot the system with the following command: # /usr/sbin/shutdown -r now
FILES
Specifies the host name file. Specifies the environment variables that define the network configuration on your system. Specifies the
trusted hosts file. Specifies the network name file. Specifies Internet routing information. Specifies Internet routing information.
SEE ALSO
Commands: mount(8), rcinet(8)
Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4).
Network Administration
ip6_setup(8)