12-27-2005
yea i have tried cstm but i don't the info on BIOS , Chassis ,Monitor & keyboard Name.
never worked with MSTM though....would it give me the reqd info?
Thnaks
Veena,
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello, i have to activate a network interface. for HPUX1100 i can command ifconfig lanx plumb.
Why doesent it works under HPUX10.20?
How can i realise it?
thanks for your help!:) (2 Replies)
Discussion started by: ortsvorsteher
2 Replies
2. HP-UX
Hi guys,
Need a favour or information on how to get it done in configuring a HPUX-11i box?I need the commands which is needed to configure the box...The pdf's in HP site is too much to look at.Is there any advice from u guys on how could i settle this problem? (7 Replies)
Discussion started by: giriplug
7 Replies
3. AIX
Hi All,
Needed commands to find Monitor , chassis & keyboard related information on AIX.
Please please please help.
Thanks
VK (2 Replies)
Discussion started by: Veenak15
2 Replies
4. HP-UX
Hi All
Please somebody send me list of admin commands used for HPUX.
Thanks
Sunanda (2 Replies)
Discussion started by: sunanda
2 Replies
5. Solaris
Hi all
Got another strange one. If I try to enquire about the hardware, the command hangs implying Ive got a hardware issue. So, if I execute :-
iostat -en
sysdef - ( stops at the devices part )
format
cfgadm -al
Anything that searches the devices, then the command hangs.
... (4 Replies)
Discussion started by: sbk1972
4 Replies
6. HP-UX
I am new for HPUX OS and want to pursue my career in HPUX Administration.
I could not able to get following information from HP.com site, that why I need an assistance to know that - can I install HPUX 11i V3 OS on old HP B2000 & B1000 workstations (these workstation are 4 to 5 year old) or not,... (5 Replies)
Discussion started by: girish.batra
5 Replies
7. Solaris
Hi guru
I want to know which company's hardware is more stable means in term of H/W faults or replacement, in case of IBM (AIX), HP (HPUX) & SUN MICROSYSTEM (Solaris) & which order also, if we go through more stable to less stable system.
Regards (1 Reply)
Discussion started by: girish.batra
1 Replies
8. Hardware
Are there any other useful hardware commands to get information about your hardware? Is there any information that can't be found with these commands?
cat /proc/cpuinfo
cat /proc/meminfo
dmesg
lspci
sudo dmidecode
cpuid | more
lspci -v | grep VGA
sudo lspci -v -s 00:02.0
sudo lspci -vvv... (12 Replies)
Discussion started by: cokedude
12 Replies
9. HP-UX
We would like to know a HP Utility or any Unix command that can give the exact status of PCI Gigabit Ethernet cable (lan cable) We had tried to execute
lanscan
ioscan -fnC lan
The status appears to be the same when the cable is plugged & unplugged and also when the lan is disabled &... (5 Replies)
Discussion started by: siva3492
5 Replies
10. HP-UX
I own a 1999 vintage HP Logic Analyzer that runs HPUX 10.20. It is a 9000/775/rock system similar to a Visualize C132L/160L system.
I'm attempting, mostly for the fun of it, to upgrade the existing slow 5MB/s-only SCSI system, with a new-er PCI card. Of course drivers is my major concern. I'd... (2 Replies)
Discussion started by: KeithM
2 Replies
mzip(1) General Commands Manual mzip(1)
Name
mzip - change protection mode and eject disk on Zip/Jaz drive
Note of warning
This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the
end of this man page for details.
Description
The mzip command is used to issue ZIP disk specific commands on Linux, Solaris or HPUX. Its syntax is:
mzip [-epqrwx]
Mzip allows the following command line options:
e Ejects the disk.
f Force eject even if the disk is mounted (must be given in addition to -e).
r Write protect the disk.
w Remove write protection.
p Password write protect.
x Password protect
u Temporarily unprotect the disk until it is ejected. The disk becomes writable, and reverts back to its old state when ejected.
q Queries the status
To remove the password, set it to one of the passwordless modes -r or -w: mzip will then ask you for the password, and unlock the disk. If
you have forgotten the password, you can get rid of it by low-level formatting the disk (using your SCSI adaptor's BIOS setup).
The ZipTools disk shipped with the drive is also password protected. On Dos or on a Mac, this password is automatically removed once the
ZipTools have been installed. From various articles posted to Usenet, I learned that the password for the tools disk is APlaceForY-
ourStuff. Mzip knows about this password, and tries it first, before prompting you for a password. Thus mzip -w z: unlocks the tools
disk. The tools disk is formatted in a special way so as to be usable both in a PC and in a Mac. On a PC, the Mac filesystem appears as a
hidden file named `partishn.mac'. You may erase it to reclaim the 50 Megs of space taken up by the Mac filesystem.
Bugs
This command is a big kludge. A proper implementation would take a rework of significant parts of mtools, but unfortunately I don't have
the time for this right now. The main downside of this implementation is that it is inefficient on some architectures (several successive
calls to mtools, which defeats mtools' caching).
See Also
Mtools' texinfo doc
Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc.
* To generate a printable copy from the texinfo doc, run the following commands:
./configure; make dvi; dvips mtools.dvi
* To generate a html copy, run:
./configure; make html
A premade html can be found at: `http://mtools.linux.lu' and also at: `http://www.tux.org/pub/knaff/mtools'
* To generate an info copy (browsable using emacs' info mode), run:
./configure; make info
The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.
mtools-3.9.8 02Jun01 mzip(1)