12-27-2005
HI,
U can get all the infor using a tool called MSTM or CSTM
i would prefer to use cstm (u should have root privilises for the same),
#cstm
cstm> map all
cstm> sel all
save this to a file and u can see all the info..
for the device drivers look at ioscan output.
for more info man ioscan
Regards
govind.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello, i have to activate a network interface. for HPUX1100 i can command ifconfig lanx plumb.
Why doesent it works under HPUX10.20?
How can i realise it?
thanks for your help!:) (2 Replies)
Discussion started by: ortsvorsteher
2 Replies
2. HP-UX
Hi guys,
Need a favour or information on how to get it done in configuring a HPUX-11i box?I need the commands which is needed to configure the box...The pdf's in HP site is too much to look at.Is there any advice from u guys on how could i settle this problem? (7 Replies)
Discussion started by: giriplug
7 Replies
3. AIX
Hi All,
Needed commands to find Monitor , chassis & keyboard related information on AIX.
Please please please help.
Thanks
VK (2 Replies)
Discussion started by: Veenak15
2 Replies
4. HP-UX
Hi All
Please somebody send me list of admin commands used for HPUX.
Thanks
Sunanda (2 Replies)
Discussion started by: sunanda
2 Replies
5. Solaris
Hi all
Got another strange one. If I try to enquire about the hardware, the command hangs implying Ive got a hardware issue. So, if I execute :-
iostat -en
sysdef - ( stops at the devices part )
format
cfgadm -al
Anything that searches the devices, then the command hangs.
... (4 Replies)
Discussion started by: sbk1972
4 Replies
6. HP-UX
I am new for HPUX OS and want to pursue my career in HPUX Administration.
I could not able to get following information from HP.com site, that why I need an assistance to know that - can I install HPUX 11i V3 OS on old HP B2000 & B1000 workstations (these workstation are 4 to 5 year old) or not,... (5 Replies)
Discussion started by: girish.batra
5 Replies
7. Solaris
Hi guru
I want to know which company's hardware is more stable means in term of H/W faults or replacement, in case of IBM (AIX), HP (HPUX) & SUN MICROSYSTEM (Solaris) & which order also, if we go through more stable to less stable system.
Regards (1 Reply)
Discussion started by: girish.batra
1 Replies
8. Hardware
Are there any other useful hardware commands to get information about your hardware? Is there any information that can't be found with these commands?
cat /proc/cpuinfo
cat /proc/meminfo
dmesg
lspci
sudo dmidecode
cpuid | more
lspci -v | grep VGA
sudo lspci -v -s 00:02.0
sudo lspci -vvv... (12 Replies)
Discussion started by: cokedude
12 Replies
9. HP-UX
We would like to know a HP Utility or any Unix command that can give the exact status of PCI Gigabit Ethernet cable (lan cable) We had tried to execute
lanscan
ioscan -fnC lan
The status appears to be the same when the cable is plugged & unplugged and also when the lan is disabled &... (5 Replies)
Discussion started by: siva3492
5 Replies
10. HP-UX
I own a 1999 vintage HP Logic Analyzer that runs HPUX 10.20. It is a 9000/775/rock system similar to a Visualize C132L/160L system.
I'm attempting, mostly for the fun of it, to upgrade the existing slow 5MB/s-only SCSI system, with a new-er PCI card. Of course drivers is my major concern. I'd... (2 Replies)
Discussion started by: KeithM
2 Replies
LEARN ABOUT HPUX
bootpquery
bootpquery(1M) bootpquery(1M)
NAME
bootpquery - send BOOTREQUEST to BOOTP server
SYNOPSIS
haddr [htype] [options]
DESCRIPTION
is a diagnostic function used to check the configuration of the Internet Bootstrap Protocol (BOOTP) server, bootpd(1M). This function can
only be run by the superuser, since it uses reserved ports.
constructs a boot request with the supplied parameters to send to the BOOTP server, and prints the contents of the BOOTP server reply (as
shown in below). Note that formats and prints RFC-1048 or CMU-style vendor information included in the BOOTREPLY.
The BOOTREQUEST packet is broadcast on the BOOTP server port, If a BOOTP server is configured to respond to the request, it returns a
BOOTREPLY packet on the BOOTP client port, can only display BOOTREPLY packets when the BOOTP server broadcasts the reply on the client port
or when the hardware address and IP address supplied in the BOOTREQUEST are those of the host on which is run.
The following options provide the information for the BOOTREQUEST:
Hardware address of the BOOTP client; used in the BOOTREQUEST.
A BOOTP server responds if it has configuration information for a host with this link-level address.
Type of address specified as
haddr; may be or The default address type is
Specify the internet address of the BOOTP client to be used in the BOOTREQUEST.
If the BOOTP client does not know its IP address, the BOOTP server supplies it in the BOOTREPLY. Otherwise, the
server returns the BOOTREPLY directly to ipaddr.
Specify the name of the BOOTP server to receive BOOTREQUEST.
When the BOOTP server is known, the BOOTREQUEST is not broadcast.
Specify a vendor name to include vendor information in the BOOTREPLAY.
vendor can be specified as or For any other vendor specification, the first four characters of the parameter are used
as the vendor magic cookie.
Specify that should broadcast the reply back. This option is only valid for on the HPUX 10.0 (or later) release(s).
Specify a boot file needed by the BOOTP client.
If a boot file is specified in the BOOTREQUEST, the BOOTP server responds only if the server host can make the file
available.
EXAMPLES
/usr/sbin/bootpquery 02608cee018e ether -s hpserver
Received BOOTREPLY from hpserver.hp.com (15.9.18.119)
Hardware Address: 02:60:8c:ee:01:8e
Hardware Type: ethernet
IP Address: 15.9.18.113
Boot file: /export/tftpdir/hp-gw2-confg
RFC 1048 Vendor Information:
Subnet Mask: 255.255.248.0
Bootfile Size: 6 512 byte blocks
Domain Name Server: 15.9.18.119
Host Name: hp-gw2
AUTHOR
was developed by HP.
SEE ALSO
bootpd(1M), tftp(1), tftpd(1M).
DARPA Internet Request For Comments RFC951, RFC1048, RFC1084, RFC1395, RFC1542 Assigned Numbers.
bootpquery(1M)