Is anyone using unix with cable modem Post: 9341

10 More Discussions You Might Find Interesting

1. IP Networking

cofiguring cable modem in red hat 7.1

It was easy in mandrake, but i don't know how in red hat. I have an Allied Telesyn AT2400/ET If it's possible in mandrake then i know it's possible in red hat.

2. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that...

3. UNIX for Dummies Questions & Answers

Linux and my cable modem

I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now?

4. UNIX for Dummies Questions & Answers

can't get my cable modem up

Caldera eDesktop 2.4 - Cable Modem my NIC card has been detected, but funny scenario: #dmesg eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef /*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module....

5. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how...

6. UNIX for Dummies Questions & Answers

cable modem to sparc

hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem , i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how...

7. UNIX for Dummies Questions & Answers

Cable Modem, Unix, XP Computer Primary, need advice setup!

I have a XP computer which is my primary. I recently, well just today installed a old version of Mandrake Linux 6.5 I had laying on a self collecting dust on a old PII 233mhz that had to be vacummed out before I could use it. I have my XP computer connected by 10/100 NIC to a cable modem. My...

8. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created...

9. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks

10. OS X (Apple)

Cannot access UNIX.com with new cable modem

Hi. I have a very strange problem, so strange I don't even know which sub-forum to post it to. Last week, my cable modem broke, so I took it back and got a new one. The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet...

LEARN ABOUT NETBSD

iy

IY(4)							   BSD Kernel Interfaces Manual 						     IY(4)

NAME

     iy -- Intel EtherExpress PRO/10 Ethernet driver (Intel i82595)

SYNOPSIS

     iy0 at isa? port {port} irq ?

DESCRIPTION

     The iy device driver supports the EtherExpress PRO/10 card, and might support other ISA cards using the same chip.

MEDIA SELECTION

     The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors.  Supported media include:

	   AUI/DIX     Standard 15 pin connector

	   10Base2     BNC, also known as thin-net

	   10BaseT     UTP, also known as twisted pair

     The default port to use is the port the card autodetects at ifconfig up time.  To choose an alternative port, an explicit medium can be spec-
     ified to ifconfig(8) or in your ifconfig.iy? file.

NOTES

     The EtherExpress PRO card has no jumpers to set the address.  Intel supplies software to set the address of the card in software.	You have
     to hardwire this address in your kernel configuration file.

SEE ALSO

     ed(4), eg(4), el(4), ep(4), intro(4), ix(4), le(4), ifconfig(8)

STANDARDS

     are great.  There's so many to choose from.

BSD
								   May 22, 1996 							       BSD