10-25-2001
The problem is that your ifconfig command puts the information into memory. This will hold until your either restart the services, or reboot.
To make the changes "stick" you will need to put the information into the config file.
For HP-UX that file is
/etc/rc.config.d/netconf
Post what OS you are using (if not HP-UX) and maybe someone
can let you know which file you need to edit.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
LEARN ABOUT DEBIAN
jifty::manual::tutorialrest
Jifty::Manual::TutorialRest(3pm) User Contributed Perl Documentation Jifty::Manual::TutorialRest(3pm)
NAME
Jifty::Manual::TutorialRest - Web Services
DESCRIPTION
This builds on Jifty::Manual::Tutorial, so make sure you have a running jifty that roughly resembles the step-by-step from there.
SETUP
You must add this to your site_config.yml
framework:
Plugins:
- REST: {}
See Jifty::Plugin::REST.
The commands assume that you have LWP installed with the GET alias. If not, you'll need to use the longhand lwp-request -m GET, or curl,
or your browser.
help
Make sure it is working:
$ GET http://localhost:8888/=/help
Accessing resources:
...
You should see some text describing the services, not html (that's longhand for 404.) Check the config and restart the server.
GET
Just list the models.
$ GET http://localhost:8888/=/model.yml
---
- MyWeblog.Model.Post
List the Post schema.
$ GET http://localhost:8888/=/model/Post.yml
---
body:
label: Content
name: body
readable: 1
sort_order: 1
type: text
writable: 1
id:
mandatory: 1
name: id
readable: 1
type: serial
writable: 0
title:
default: Untitled post
label: Title
name: title
readable: 1
sort_order: 0
type: text
writable: 1
You did make some posts, right?
$ GET http://localhost:8888/=/model/Post/id.yml
---
- 1
- 2
Dump the data:
$ GET http://localhost:8888/=/model/Post/id/1.yml
---
body: 'This is my post, the content of which is this, which is mine.'
id: 1
title: my first post
$ GET http://localhost:8888/=/model/Post/id/2.yml
---
body: "Content of another post. Got to go, the cat's on fire."
id: 2
title: post deux
POST
TODO not working
Actually, it looks like it is not supposed to work this way. Why not?
$ echo '---
body: "A post via web services"
id: 3
title: "posting from the command-line"
' | lwp-request -m POST http://localhost:8888/=/model/Post.yml
POST http://localhost:8888/=/model/Post/id/3.yml --> 404 Not Found
PUT
TODO not working
$ echo '---
title: "posting from the cli"
' | lwp-request -m PUT http://localhost:8888/=/model/Post/3.yml
500 Can't read entity body: Connection reset by peer
DELETE
$ lwp-request -m DELETE http://localhost:8888/=/model/Post/id/3.yml
---
content: {}
error: ~
field_errors: {}
field_warnings: {}
message: Deleted
success: 1
perl v5.14.2 2010-09-25 Jifty::Manual::TutorialRest(3pm)