Sponsored Content
Special Forums IP Networking Quad Fast Ethernet Card on Sparc 10? Post 9258 by doeboy on Wednesday 24th of October 2001 04:41:32 PM
Old 10-24-2001
Did you make sure the hostname for each respective interface is contained in each hostname.qex file?

BTW... That is a Quad-Ethernet card. Quad-Fast Ethernet cards are identified as qfe. (Just in case you bought a card thinking it was qfe and not getting 100mbit)
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ... (2 Replies)
Discussion started by: sameergrover
2 Replies

8. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies

10. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
HME(4)							   BSD Kernel Interfaces Manual 						    HME(4)

NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device miibus device hme Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_hme_load="YES" DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces. All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and transmission of extended frames for vlan(4) and a 128-bit multicast hash filter. HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models. Cards supported by the hme driver include: o Sun PCI SunSwift Adapter (``SUNW,hme'') o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'') o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'') o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'') o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'') o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'') NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC address. Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all add-on cards except the single-port SBus versions. SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8) Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf, April 1996. HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0. AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>. BSD
June 14, 2009 BSD
All times are GMT -4. The time now is 07:00 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy