12-08-2005
Just found out that the server was installed with no network options. Used sys-unconfig to rectify this
9 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
3. UNIX for Advanced & Expert Users
I have an E420 server that has a TPE Slot / NIC installed.
However there is no interface file installed eg /etc/hostname.hme0 or equivalent.
I have placed a private ip entry int the hosts file to accompany the loop back entry i.e.
127.0.0.1 localhost
172.16.0.10 loghost se420
... (1 Reply)
Discussion started by: jimthompson
1 Replies
4. IP Networking
I have an E420 server that has a TPE Slot / NIC installed.
However there is no interface file installed eg /etc/hostname.hme0 or equivalent.
I have placed a private ip entry int the hosts file to accompany the loop back entry i.e.
127.0.0.1 localhost
172.16.0.10 loghost se420
... (1 Reply)
Discussion started by: jimthompson
1 Replies
5. SCO
hi all
i have installed SCO 5.0.5 on a "Netfinity 5000" IBM server. But the OS is not detecting the lan card. how can i detect it.... help and thanks in advance .
bidhayak (3 Replies)
Discussion started by: bidhayakm
3 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
I have installed solaris10 x86 on HP DL380 G5 Server, but network card is not getting detected.
i have installed the network driver, downloaded from the following link
HP ProLiant DL380 G5 Server series- Download drivers and software - HP Business Support Center
Can any one suggest me how to... (1 Reply)
Discussion started by: raj.chinnu
1 Replies
8. Solaris
Hi All,
Anyone has configured a Sunix Sata S150 card (AKA Initio Inic-1622) + disk in a Solaris10/x86 05/09 system? I wondered what to do to get it running. The Sunix card does not come with a Solaris driver ;-(
The card is seen by the system as the prtconf -v output shows (see below at the... (0 Replies)
Discussion started by: longwave
0 Replies
9. Red Hat
Dear Expert,
I 've installed Redhat linux AS3, My machine having Inbuild network card (Intel(R) 82566DM-2 Gigabit Network Connection).
I've downloaded e1000e-2.3.2 from Intel site, but its not working for my machine. I'm unable to configure the Network.
ifconfig eth0 xx.xx.xx.xx netmask... (0 Replies)
Discussion started by: Mohammed Faiz
0 Replies
HOSTS(5) File Formats Manual HOSTS(5)
NAME
hosts - host name data base
DESCRIPTION
The hosts file contains information regarding the known hosts on the network. For each host a single line should be present with the fol-
lowing information:
official host name
Internet address
aliases
Items are separated by any number of blanks and/or tab characters. A ``#'' indicates the beginning of a comment; characters up to the end
of the line are not interpreted by routines which search the file.
When using the name server named(8), this file provides a backup when the name server is not running. For the name server, it is suggested
that only a few addresses be included in this file. These include address for the local interfaces that ifconfig(8C) needs at boot time
and a few machines on the local network.
This file may be created from the official host data base maintained at the Network Information Control Center (NIC), though local changes
may be required to bring it up to date regarding unofficial aliases and/or unknown hosts. As the data base maintained at NIC is incom-
plete, use of the name server is recommend for sites on the DARPA Internet.
Network addresses are specified in the conventional ``.'' notation using the inet_addr() routine from the Internet address manipulation
library, inet(3N). Host names may contain any printable character other than a field delimiter, newline, or comment character.
FILES
/etc/hosts
SEE ALSO
gethostbyname(3N), ifconfig(8C), named(8)
Name Server Operations Guide for BIND
4.2 Berkeley Distribution May 14, 1986 HOSTS(5)