11-24-2005
hme0 problem after reboot
Hi .....
My problem is that when i reboot the system i can't connect to the network because my ethernet ( hme0 ) is down , i must up it by ifconfig command
after reboot :
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
hme0: flags=1000843<BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet x.xxx.xxx.xx netmask ff000000 broadcast x.xxx.xxx.xxx
ether 8:0:20:e8:e0:c2
i must type ifconfig hme0 up all time after reboot , my question is there is a way to setup it aumatically ?
OS: SUN SOLARIS 9 ON SUN SPARC SERVER
TNKS IN ADVANCE !!!!!!!!
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Reader,
I have a very unique problem. Quite often my on board ethernet port( hme0 ) related message is appearing in /var/adm/messages.
The message is hme0: babble.. The port is up and alive.
What does this message mean.. Is the on board port is about to fail??
Thanks in advance, (2 Replies)
Discussion started by: joseph_shibu
2 Replies
2. UNIX for Advanced & Expert Users
How do you configure more than one network on a single hme0 interface under SunOS? And why would you want to do this?
Thanx :)
-Michelle (1 Reply)
Discussion started by: Michelle1977
1 Replies
3. Solaris
Operatin System : Solaris 5.9
Server : Sun Fire 3800
Shutdown and reboot i receive the following messages .....
un Fire 3800
OpenFirmware version 5.15.2 (08/04/03 10:27)
Copyright 2001-2003 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
SmartFirmware,... (8 Replies)
Discussion started by: tt155
8 Replies
4. UNIX for Dummies Questions & Answers
Hi, i have sco openserver 5.0.6 but have a problem with shutdown or reboot commands.
The string I use is "shutdown -g0 -y" but the system just hangs on "The sytem is down" . I used to get a "Safe to turn of" but now nothing. Same with "reboot" the sytem just freezes.
Any suggestions? (1 Reply)
Discussion started by: VTechman
1 Replies
5. UNIX for Dummies Questions & Answers
I have sun solaris 9 installed but I have the interface configured to hme1 instead of hme0, our default value.
Is there a way where i can rename the existing/working hme1 to hme0...?
I want to showup the hmeo up if i say ifconfig -a..
rite now i see the hme1 up..
please advice if possible... (4 Replies)
Discussion started by: tintedwindow
4 Replies
6. Solaris
I have a 420r server it boots up all of the network settings are correct, however the machines network connection is not working. Cant ping anything from it, cant ping it from another machine on the network.
If I ping 127.0.0.1 it says alive.
Is there a chance the network card has been... (2 Replies)
Discussion started by: alanj4
2 Replies
7. UNIX for Advanced & Expert Users
Hi All,
I am facing a connection problem with Oracle 10g on Solaris 10 when my application (started by /etc/rc3.d at node reboot) tries to establish a session after reboot of the node where my application is running (NCR UNIX (MP RAS)).
I find that my application (run as a deamon process)... (1 Reply)
Discussion started by: sowjanya
1 Replies
8. Solaris
Ultra E150 Solaris 2.5.1 Oracle server. was working fine, then started losing network connection. I can see in messages file that it was complaining about another device using its ip address. Though not any longer, though I wonder if that was a red herring. My IT guys have now re-reserved its ip... (29 Replies)
Discussion started by: AlSmith1964
29 Replies
9. Linux
I have a linux server,in this i receive alarm as server has rebooted.
When i check uptime of the server it says that the server has rebooted but when i check output of who -b it says that the server rebooted very long back
Can some one help what is the issue here. (3 Replies)
Discussion started by: tiwsaj
3 Replies
10. Solaris
Hiii folks,,
I am unable to configure NIC using hme0 command. I am getting an error message as "hme0: File or directory not found.."
can someone help me...
Bhagi... (9 Replies)
Discussion started by: bhargav90
9 Replies
LEARN ABOUT ULTRIX
reboot
reboot(8) System Manager's Manual reboot(8)
Name
reboot - automatic reboot procedures
Syntax
/etc/reboot [ -n ] [ -q ]
Description
The ULTRIX system is booted by loading a kernel image, usually into memory at location zero and transferring to zero. Because the system
is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.
When the reboot of a running system is desired, is normally used. If there are no users, can be used. The command causes the disks to be
synced, and then a multiuser reboot is initiated. The system is booted and an automatic disk check is performed. If the procedure suc-
ceeds, the system is then brought up for the users.
The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system. A consistency check
of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.
Options
-n Prevents the disks from being synced.
-q Reboots quickly and ungracefully, without shutting down running processes first.
Files
System code
See Also
crash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)
reboot(8)