10-21-2001
serial port reading
Hai there,
Can any one provide me with a ansi c source code for
opening com1 or com2 and read data. The port is connected to
another serial communication device on rs232 port.
The o/s is Sco Unix 5.0.6
Matter urgent
Viswanath
Last edited by viswanath; 10-22-2001 at 11:52 AM..
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I am using system running on red hat linux 4.
I had connected health measuring machine to the serial port and configured it
stty -F /dev/ttyS0 9600 -parenb cs8 -cstopb
this machine requires a command to be passed to it for giving output. I am unable to pass command hexa format(0x68) to the... (4 Replies)
Discussion started by: netsavant
4 Replies
2. SCO
Hi
I have just re-installed Compaq ML350 G2 Server with Unix SCO 5.0.5 and
informix DBMS .
on this server we have 2 serial ports , unfortunately its not working.
Can anyone help me to check the serial ports working or not OR guide me
to reconfigure it.
I have attached a device with... (1 Reply)
Discussion started by: munirh
1 Replies
3. Linux
Hi All,
I am a begineer in Linux, I have 4 ports and 3 are operational port 1,port 2 and port 4 (when I plug in serial device I can see it working) but port 3 seems it is not working.
I am sure the hardware is fine.
when I give command
dmesg | grep tty
I get,
serial 8250:ttyS0 at... (0 Replies)
Discussion started by: vr_82
0 Replies
4. Programming
I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than... (2 Replies)
Discussion started by: raj8109
2 Replies
5. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
6. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
7. Shell Programming and Scripting
hello all,
please any one can provide me the shell script to write data to /dev/ttyS1
and read responce from /dev/ttyS1 and compare the responce to some string ..
thnxx
---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ----------
any body help me..
how do i... (1 Reply)
Discussion started by: yashwantkumar
1 Replies
8. Debian
Dear List -
I am trying to capture data from a serial port and write it to a file.
/var/www$ cat /dev/ttyS0 > scale_value.html
cat: /dev/ttyS0: Device or resource busy
/var/www# cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:90... (11 Replies)
Discussion started by: Meow613
11 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
RTFPS(4) BSD Kernel Interfaces Manual RTFPS(4)
NAME
rtfps -- multiplexing serial communications interface
SYNOPSIS
rtfps0 at isa? port 0x1230 irq 10
com2 at rtfps0 slave 0
com3 at rtfps0 slave 1
com4 at rtfps0 slave 2
com5 at rtfps0 slave 3
DESCRIPTION
The rtfps driver provides support for IBM RT PC boards that multiplex together up to four EIA RS-232C (CCITT V.28) or RS-422A communications
interfaces.
Each rtfps device is the master device for up to four com devices. The kernel configuration specifies these com devices as slave devices of
the rtfps device, as shown in the synopsis. The port specification for the rtfps device is used to compute the base addresses for the com
subdevices.
FILES
/dev/tty0?
SEE ALSO
com(4)
HISTORY
The rtfps driver was written by Charles Hannum, based on the ast driver.
BUGS
The rtfps driver is unlikely to work on non-EISA and non-PCI machines. The ISA bus only asserts 10 I/O address lines, and this is not
enough.
Even on EISA and PCI machines, some address conflicts have been observed. On one machine, the second port always conflicted with something
(though it's not clear what) and caused strange results. Disabling the second port in the kernel config allowed the other three ports to
function correctly.
BSD
August 7, 1994 BSD