11-08-2005
M p unknown unknown /dev/dsk/c1t1d0s4 << bad disk
M p unknown unknown /dev/dsk/c1t3d0s4 << bad disk
Note in your metadb - looks like someone added to the metadb but never rebooted - that's usually why you get the unknown in the status although it's possible you are also getting it because the disks are bad. The good thing is that there are so many copies of the metadb - so you can replace the bad disks without no worry about losing anything.
As far as the bad disk, get the replacement disk drives and you can use the metareplace command. Or you can use metadetach and metaclear to remove them from the metastat and replace the drives, format, and readd them. You can hot swap the drives so you should not need any down time.
Also, insure that the boot device is c1t0d0s0 and not c1t1d0s0. You don't want to hot swap or remove the drive you are booted off of (inital boot will be off one drive and then the mirrors come into play). Just check the output of eeprom and look for boot-device - hopefully it isn't simply "disk:a" but gives you the output that you would be able to tell which drive it really is. If not, then you can play it safe and reboot into single user to do the drive replacements. More info can be found
in this thread
10 More Discussions You Might Find Interesting
1. Solaris
Hi Guys,
Need to add 2 disks into a JBOD array (3310).
Does anyone see anything wrong with my Procedure / Doco below?
1> Logon to system, check system logs for abnormal entries.
2> Make backups of related system files:
A>cp -p /etc/system /etc/system.backup.081505
B>cp -p /etc/vfstab... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies
2. Solaris
hi expert,
sorry i'm new in solaris system, need more advice and help :)
i'm confusing with mirroring disk at my sparc v890 solaris 8, i have 6 harddisk which the structure shown below :
format :
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>
... (4 Replies)
Discussion started by: bucci
4 Replies
3. Solaris
Hi
I have a Sunfire X4100 box with a 4 disk Chassis (although I only have 2 disks in it). I have been asked to add two more disks into the chassis so that I can mirror the original two using SVM .....Ive read through a couple of SVM docs but am finding it a little confusing, and if any of you... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
4. Solaris
I am having an issue with setting up disk mirroring for Solaris 10 on an x86 server. My main problem is that the volumes and slices have already been setup and our proprietary software has already been installed and configured. The entire drive has been allocated in this configuration and the... (2 Replies)
Discussion started by: chuck43
2 Replies
5. Solaris
Has anyone managed to set up disk mirroring in Solaris 10 yet? If so can you point me in the direction of some useful documentation please.
Cheers (25 Replies)
Discussion started by: korfnz
25 Replies
6. Solaris
Hi Friends,
I am having Sun Solaris 5.8 OS installed having 2 different size hard disk, sizes are c0t0d0s0(160 GB) and c0t2d0s0 (40GB). I have installed Sun Solaris 5.8 OS in c0t0d0s0 (160GB) harddisk.
I have configured all the parameters required for disk mirroring. But when executing... (4 Replies)
Discussion started by: Vijayakumarpc
4 Replies
7. Solaris
Need a procedure document to do "root disk mirroring in solaris volume manager for solaris 10". I hope some one will help me asap. I need to do it production environment.
Let me know if you need any deatils on this.
Thanks,
Rama (1 Reply)
Discussion started by: ramareddi16
1 Replies
8. Solaris
Hi Guys,
I have an issue with my Hotspares/Metastat on an x4270m2.
I have no hotspares available, when i printed out my metastat i got
d21: Concat/Stripe
Size: 33559785 blocks (16 GB)
Stripe 0:
Device Start Block Dbase Reloc
... (0 Replies)
Discussion started by: A-Train
0 Replies
9. Solaris
I would like to perform root disk mirroring task. Can someone please help me out on this.
Thanks !!
Regards,
Rama (2 Replies)
Discussion started by: ramagore85
2 Replies
10. Solaris
I have 2 disks in my system.I recently added a zpool to the disk, but today I changed my mind and deleted the zpool ,
zpool destroy -f extra
The zpool is now deleted and I want to partition the disk, so I delete the only partition on the disk.
Now when I run format again,
format... (13 Replies)
Discussion started by: cbtshare
13 Replies
LEARN ABOUT OSF1
volmirror
volmirror(8) System Manager's Manual volmirror(8)
NAME
volmirror - Mirrors volumes on a disk or control default mirroring
SYNOPSIS
/usr/sbin/volmirror [-g diskgroup] [-d yes|no] medianame [new_medianame...]
/usr/sbin/volmirror [-g diskgroup] [-d yes|no] -a [new_medianame...]
/usr/sbin/volmirror [-g diskgroup] [-d yes|no]
/usr/sbin/volmirror [-g diskgroup] -D
OPTIONS
The volmirror command supports the following options: Limits operation of the command to the given disk group, as specified by disk group
ID or disk group name. The medianame operands will be evaluated relative to the given disk group. If no disk group is supplied to the
volmirror command, rootdg is presumed. Changes the default for subsequent volume creation, depending on the option argument. If the option
argument is yes, all subsequent volumes created using the volassist command will automatically be created as mirrored volumes. If the
option argument supplied is no, mirroring will be turned off for future volumes by default. Displays current default status for mirroring.
Mirrors all existing volumes for the specified disk group.
DESCRIPTION
The volmirror command provides a mechanism to mirror all the contents of a specified disk, to mirror all currently unmirrored volumes in
the specified disk group, or to change or display the current defaults for mirroring. All volumes that have only a single plex (mirror
copy), will be mirrored by adding an additional plex.
Volumes containing subdisks that reside on more than one disk will not be mirrored by volmirror.
The volmirror command is generally called from the voldiskadm menus. It is not an interactive command and once called, will continue until
completion of the operation or until a failure is detected.
Note
Due to the nature of generating mirror copies of volumes, this command may take a considerable time to complete.
In the first listed form of the command, the disk media name is supplied on the command line to volmirror. That name is taken to be the
only disk from which volumes should be mirrored. In the case of mirroring volumes from a specified disk, only simple single-subdisk volumes
are mirrored.
In the first and second listed forms of the command, the new_medianame ... parameter identifies a new disk media name (or set of names).
The mirroring operation being performed will use these names as targets on which to allocate the mirrors. An error will result if the same
disk is specified for both the source and target disk and if no other viable targets are supplied.
EXAMPLES
The following are examples of the use of the volmirror command. The following command mirrors the contents of the disk named disk01 to any
available space on any available disk. Subsequent calls to volassist will cause created volumes to be mirrored by default. volmirror -d
yes disk01 The following command displays the current status of default mirroring. It prints the string yes if mirroring is currently
enabled or no, if not. volmirror -D The following command mirrors any volumes on disk02 onto disk03. volmirror disk02 disk03
FILES
The defaults file for volassist parameters.
SEE ALSO
volintro(8), volassist(8), volrootmir(8)
volmirror(8)