10-14-2005
Thanks for the suggestions,
Actually i was trying to configure a Vip on same physical interface lan0:0 , which didnt work
so i tryed
ifconfig lan0:1 <IP> up
It indeed worked.
Thanks once again
10 More Discussions You Might Find Interesting
1. HP-UX
OS - HP-UX B.10.20 A 9000/777
Anyone know how to set up a virtual interface on HP-UX?
I've looked quickly through docs.hp.com and searched this site. No luck. And my HP Guru is sleeping today. (4 Replies)
Discussion started by: thehoghunter
4 Replies
2. HP-UX
Hello all,
I have configured a virtual interface using ifconfig on HP UX 11.11.
When i try to do traceroute with -i option i get * * * from traceroute.
i use $traceroute -i lan0:1 my-gateway
traceroute to my-gateway (15.70.180.1), 30 hops max, 40 byte packets
1 * * *
2 * * *
30 * *... (2 Replies)
Discussion started by: supersumanth
2 Replies
3. IP Networking
Hi all,
I am experiencing a problem with dhcp broadcast packages. these broadcast packages are seen on bge1 and bge1:1 interfaces but somehow they are not seen at bge771001 interface which is second virtual interface on the bge1 interface.
I have a server on which I configured it as working... (2 Replies)
Discussion started by: ironoxide
2 Replies
4. Shell Programming and Scripting
How would i create virtual interface in linux to configure more than one IP address for a physical interface?
any help wll be appreciated.
https://www.unix.com/images/misc/progress.gif (1 Reply)
Discussion started by: salil2012
1 Replies
5. IP Networking
Hi ,
by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces.
would some one help me out in this.
Thanks
Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies
6. AIX
Hi,
I am totally new to AIX. I would like to know how to create virtual interface on AIX machine.
Thanks,
Pooja (4 Replies)
Discussion started by: pooja84k
4 Replies
7. IP Networking
Hello everybody,
I have been reading many posts about this topic but I have no figure out how to solve it.
I need to split the traffic incoming on eth0 on two other interfaces (for instance one receiving on port 80 and the others on the other interface).
I cannot understand how to do that.... (2 Replies)
Discussion started by: nicandro
2 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. IP Networking
Hello, I'm trying to route all packets arriving at a particular interface by entering the same interface
the virtual interface eth1: 2 and now everything is routed by default gw configured on eth1.
eth1 Link encap:Ethernet HWaddr 0a:0e:64:18:52:72
inet addr:192.168.10.15
eth1:2 ... (1 Reply)
Discussion started by: faka
1 Replies
10. AIX
Note: Newbie to IBM virtualization :-)
Query: Created a new AIX7.1 lpar on a system with same config as one before however the new one is having issues going out to physical network.
Now on comparison the only thing which differs between these two machines is an additional en1 and ent1 shown... (7 Replies)
Discussion started by: max
7 Replies
AGR(4) BSD Kernel Interfaces Manual AGR(4)
NAME
agr -- link aggregation pseudo network interface driver
SYNOPSIS
pseudo-device agr
DESCRIPTION
The agr driver provides link aggregation functionality (a.k.a. L2 trunking or bonding).
It supports the IEEE 802.3ad Link Aggregation Control Protocol (LACP) and the Marker Protocol.
The agr driver supports the following link specific flags for ifconfig(8):
link0 Use the round-robin distribution algorithm. Don't use it unless you're really sure, because it violates the frame ordering rule.
-link0 Use the default distribution algorithm, which is based on the hash of DA/SA, TCI, and, if available, some upper layer protocol infor-
mation like ip(4) DA/SA.
link1 Disable LACP. Prevents any LACP or Marker messaging which leaves the ports in the default static configuration. Set this prior to
adding ports.
EXAMPLES
Create an agr interface, agr0, and attach re0 and re1 to it. In other words, aggregate re0 and re1 so that they can be used as a single
interface, agr0. The physical interfaces which are attached to the agr interface must not have any IP addresses, neither IPv4 nor IPv6.
ifconfig re0 inet xxx.xxx.xxx.xxx delete
ifconfig re0 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig re1 inet xxx.xxx.xxx.xxx delete
ifconfig re1 inet6 fe80::xxxx:xxxx:xxxx:xxxx delete
ifconfig agr0 create
ifconfig agr0 agrport re0
ifconfig agr0 agrport re1
Destroy an interface created in the above example.
ifconfig agr0 -agrport re0
ifconfig agr0 -agrport re1
ifconfig agr0 destroy
SEE ALSO
ifconfig(8)
STANDARDS
IEEE 802.3ad Aggregation of Multiple Link Segments
HISTORY
The agr driver first appeared in NetBSD 4.0.
AUTHORS
The agr driver was written by YAMAMOTO Takashi.
BUGS
There is no way to configure LACP administrative variables, including system and port priorities. The current implementation of the agr
driver always performs active-mode LACP and uses 0x8000 as system and port priorities.
The agr driver uses the MAC address of the first-added physical interface as the MAC address of the agr interface itself. Thus, removing the
physical interface and using it for another purpose can result in non-unique MAC addresses.
The current implementation of the agr driver doesn't prevent unsafe operations like some ioctls against underlying physical interfaces. Such
operations can result in unexpected behaviors, and are strongly discouraged.
There is no way to configure agr interfaces without attaching physical interfaces.
Physical interfaces being added to the agr interface shouldn't have any addresses except for link level address. Otherwise, the attempt will
fail with EBUSY. Note that it includes an automatically assigned IPv6 link-local address.
BSD
February 23, 2010 BSD