10-13-2005
You need to know who the manufacture of the SCSI card is, then download the SCO drivers from the manufactures web site.
Do a man on boot and it will show you how to add specific cards.
9 More Discussions You Might Find Interesting
1. Red Hat
my redhat 9 will not boot. We had a power failure and when the power came back, my redhat linux will not boot.
The machine come up to grub prompt.
I tried the following from grub prompt
root (hd0, then press tab key
partition num:0 filesystem type unknown, partition type 0x83... (7 Replies)
Discussion started by: hassan2
7 Replies
2. UNIX for Advanced & Expert Users
Hey !
I am running EWS-UX/V (Rel 4.2) on NEC EWS/4800/330 station and I am having problems rebooting my station : I am getting the following message on display : BOOT : PANIC : File size out of range.
According to user guide, this error is occuring when a file exceeding the limit and/or... (2 Replies)
Discussion started by: fredo
2 Replies
3. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
4. Solaris
I'm running solaris 2.5.1. My main development server is DEAD, i can't even boot off the cdrom, it powers up, acts like it is starting the boot process but then says cannot find boot device. I've done the search here on this site and saw the other posts, but at the ok prompt it won't even let me... (3 Replies)
Discussion started by: kymberm
3 Replies
5. SCO
hi
SCO Unix 5.0.6 doesn't boot due to this problem:
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot
Knows someone howto solve it? (16 Replies)
Discussion started by: ccc
16 Replies
6. Boot Loaders
Hello,
I have kubuntu on my laptop and now I decided to switch to Windows 7. I made the bios settings properly (first choice is boot from cd\vd) but I see the error
" reboot and select proper Boot device or insert Boot media in select Boot device and press a key "
I have tried CD and... (0 Replies)
Discussion started by: rpf
0 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
Hi Solaris 10 Experts,
I am wondering what is the correct syntax to edit in Grub when trying to specify the local ZFS boot disk while booting up from a Solaris 10 x86 64bits DVD installation disk. In other word, I try to boot up from local disk without removing the Solaris installation disk... (0 Replies)
Discussion started by: gjackson123
0 Replies
9. Solaris
Hello,
I have a problem with my machine that won't boot properly.
The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
DAIC(4) BSD Kernel Interfaces Manual DAIC(4)
NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards
SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10
DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO.
For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd
system, which can be listed using the daicctl utility.
The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should
allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto-
col and some parts of the cards interface are ISDN protocol dependent.
The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992.
MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd.
Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l
to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu-
mentation for details.
The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called
download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under
dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile
will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte-
grated. But if you own a card, you do have the file (or can get it from the Diehl web server).
SEE ALSO
daicctl(1)
BUGS
The driver is not yet finished.
BSD
January 30, 1998 BSD