Sponsored Content
Full Discussion: bind zone transfer?
Special Forums IP Networking bind zone transfer? Post 8622 by PxT on Monday 15th of October 2001 12:49:39 PM
Old 10-15-2001
BIND allows you to explicitly specify which hosts you will allow transfers to. usually you will specify just your secondary nameservers. The syntax is:

xfernets 192.168.0.1&255.255.255.255


Replace 192.168.0.1 with whatever the IP of your seconday server is. All other IP's will be denied. Note that you must follow the syntax exactly (no additional whitespace allowed). Check out the BIND docs for more, or read the "Ask Mr DNS" website which answers just about every DNS-related question you could think of: http://www.acmebw.com/askmrdns
 

9 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

zone transfer - free site

Dear all, Did anyone in this forum know site that offer free DNS zone transfer? if anyon know, please reply my message. Thanks (0 Replies)
Discussion started by: unknown2205
0 Replies

2. Solaris

Bind zone transfer recategorises zone file?

Hi, I have a primary/slave Bind 9 setup running on a Solaris 10 platform. Everything is hunky dorey, except for when I make a zone file change and up the serial the file that is transferred to the slave looses all its comments, and the entries are place in alphabetical order. I administer many... (1 Reply)
Discussion started by: fulhamfcboy
1 Replies

3. Solaris

How to obtain DNS Zone transfer settings on Sun OS 5.7

I have an old Sun SparcStation 5 that is running Sun OS 5.7, I'm not sure which commands would allow me to obtain the DNS zone transfer settings? 1.) I'm needing to know if the zone transfers are enabled. 2.) If it is enabled, does it transfer to specific servers 3.) If so, how do I go about... (1 Reply)
Discussion started by: Fhistleb
1 Replies

4. Solaris

Zone failes to boot due to mount issue, dir exists in zone.

I have two physical servers, with zones that mount local storage. We were using "raw device" in the zonecfg to point to a metadevice on the global zone (it was not mounted in the global zone at any point). It failed to mount on every boot because the directory existed in the zone. I... (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies

5. Solaris

DNS zone transfer Problem.

Hi All , I have 2 DNS servers (BIND 9.6.1 -Solaris 10) .Its configured as master ,slave serves .Now i am recieving error messages related to zone transfer in both the servers as mentioned below . Primar Server named: client x.x.x.x#40825: transfer of './IN': sending zone data: ran... (1 Reply)
Discussion started by: sandeep.tk
1 Replies

6. Solaris

showing 2 different time zones in global zone and nonglobal zone

can some one help me out as it is showing 2 different time zones in global zone and nonglobal zone .In global zone it is showing in GMT while in nonglobal zone i it showing as PDT. System in running with solaris 10 (3 Replies)
Discussion started by: ravijanjanam12
3 Replies

7. Ubuntu

Bind dns server zone file

I have a couple of zone conf files for the BIND server. There are some records that contains the "IN" statement and some do not. But anyway this works. So my question is what this "IN" is intended for? Here is the zone file example: ORIGIN . $ttl 60 example.com. IN SOA ... (4 Replies)
Discussion started by: andriesh
4 Replies

8. UNIX for Advanced & Expert Users

Solaris 10: I forgot to detach a zone before zpool export. Uninstall zone?

Dear all, recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes. I did the following: host1: $ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed $ zpool export zone1 host2: $ zpool... (2 Replies)
Discussion started by: custos
2 Replies

9. Solaris

Solaris 11 zone has no external network access (except to Global Zone)

Hi, hoping someone can help, its been a while since I used Solaris. After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin) However, the NGZ cannot access any other netwqork devices, it can't even see the default router ... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
App::AllKnowingDNS::Config(3pm) 			User Contributed Perl Documentation			   App::AllKnowingDNS::Config(3pm)

NAME
App::AllKnowingDNS::Config - configuration object DESCRIPTION
Note: User documentation is in all-knowing-dns(1). This module defines an object which holds the parsed version of the AllKnowingDNS configuration file. FUNCTIONS
zone_for_ptr($zone) Returns the appropriate zone for the given PTR query or undef if there is no appropriate zone. Example: my $query = '7.c.e.2.3.4.e.f.f.f.b.d.9.1.2.0.' . '0.c.c.c.e.0.0.1.8.8.d.4.1.0.0.2.ip6.arpa'; my $zone = $config->zone_for_ptr($query); return 'NXDOMAIN' unless defined($zone); ... zone_for_aaaa($zone) Returns the appropriate zone for the given AAAA query or undef if there is no appropriate zone. Example: my $query = 'ipv6-foo.nutzer.raumzeitlabor.de'; my $zone = $config->zone_for_aaaa($query); return 'NXDOMAIN' unless defined($zone); ... VERSION
Version 1.3 AUTHOR
Michael Stapelberg, "<michael at stapelberg.de>" LICENSE AND COPYRIGHT
Copyright 2012 Michael Stapelberg. This program is free software; you can redistribute it and/or modify it under the terms of the BSD license. perl v5.14.2 2012-03-28 App::AllKnowingDNS::Config(3pm)
All times are GMT -4. The time now is 04:34 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy