09-22-2005
A little hard to know whats going on without a bit more information. Such as what the configuration files were changed from and to.
I general though, for solaris, you need to check the following.
1) /etc/hostname.<id>
where <id> is the identifier for the ethernet card in the machine. There will be one of these files for each physical and logical interface defined on your system (so probably only 1 file in your case). It should contain the hostname (without domain name) of your machine.
2) /etc/hosts
should contain a line (or lines) which match the host names from the file(s) in point 1. The format of each line would (in its simplest form) be
<ip address> <hostname>
3) If you are using any other subnet mask other than a standard class A B or C the mask for the particular network needs to be present in /etc/netmasks
4) /etc/defaultrouter
should contain the IP address of your default router.
5) /etc/defaultdomain
should contain your domain name
6) There are several other files where information on the hostname and ip address are stored they are mostly not hand edited. If your machine has had its ip address only partially changed then it may well be easier to run the 'sysunconfig' command, reboot and answer all the relevant questions on boot up. I would *NOT* however suggest you do this without an experienced admin present.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Have a Sun CDROM connected to a Ultra machine .
Problem is it is not recognizing the drive being connected to it ...
When i put the CD in the drive it accepts the CD and zooms initially then quitens out ..
The devices drivers are also not created for it ...
Any ideas anyone ... I am... (4 Replies)
Discussion started by: Jai
4 Replies
2. Solaris
Good Day,
I've remotely mounted a cdrom (no problems theere). The kicker is I can see the directories on the remote CD bout I can't see the files. What am I doing wrong? I'm logged in as root on both systems. All the permissions seem okay - what am I missing? Thanks (2 Replies)
Discussion started by: greg69
2 Replies
3. Solaris
Morning all,
I am attempting to load a package from a Solaris 8 CDROM.
This fails with the error :
"pkgadd: ERROR: unable to access pkgmap file </cdrom/ .........../SUNWlibC/pkgmap>
No changes were made to the system"
Any help would be appreciated
Andy (6 Replies)
Discussion started by: AndyD
6 Replies
4. Solaris
version of solaris: SunOS 5.8 Generic-117350-39 sun4u sparc SUNW,Netra-240
version of SSH: OpenSSH_4.4p1, OpenSSL 0.9.8d 28 Sep 2006
Task:
I need to have another Machine ssh into my machine, by either RSA authentication or username/pass authentication.
History:
In the begining my... (4 Replies)
Discussion started by: EWTGPAC
4 Replies
5. HP-UX
Having a problem attaching a DVD drive to this N Class server and just wondering if anyone’s come across this before.
As there’s no space internally for a DVD drive it has one of these:
see attached pic (the rear connector says it's a single ended device)
Which I’ve tried connecting... (4 Replies)
Discussion started by: Turlock
4 Replies
6. Solaris
Greetings Forumers!
I've been fighting a locale problem on a v490 running Solaris 10 u4 (8/07). When I login to the system, I get several "locale" error messages:
user1's password:
Last login: Wed May 26 2010 09:14:13 -0400 from system1
You have mail.
couldn't set locale correctly
couldn't... (0 Replies)
Discussion started by: bluescreen
0 Replies
7. Solaris
Hey,
I have been battling with jumpstart for the past few days. Interface nxge0 is set on a vlan:
nxge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 0.0.0.0 netmask ff000000
ether 0:21:28:3c:a0:6
nxge998000:... (0 Replies)
Discussion started by: stantonnet
0 Replies
8. AIX
Hi.
I've setup a wpar on aix
mkwpar -h ibmunix2 -i -r -N interface=en0 address=10.6.0.1 netmask=255.255.255.0 -n ibmunix2
When i log into ibmunix2 it can't ping any external host,include the ibm host.
How to set route for network please?
I've set ibmunix2 with a different subnet.
... (7 Replies)
Discussion started by: Linusolaradm1
7 Replies
9. AIX
Hi all
With the recent virus attacks we have been tasked with upgrading Samba to a "secure" version. Currently running 3.0.29a and looking to put the latest version down 4.6.5.
Being a lazy bod I have only ever installed this, a long time ago, when you could get it in BFF filesets. Have... (6 Replies)
Discussion started by: splattty
6 Replies
route(8c) route(8c)
Name
route - manually manipulate the routing tables
Syntax
/etc/route [ -f ] [ -n ] command args ]
Description
The program is used to manipulate the network routing tables manually. However, normally it is not needed, as the system routing table
management daemon, should tend to this task.
The program accepts two commands: add, to add a route and delete, to delete a route.
All commands have the following syntax:
/etc/route command [ net | host ] destination gateway [ metric ]
In this syntax, destination is a host or network for which the route is to, gateway is the gateway to which packets should be addressed,
and metric is an optional count indicating the number of hops to the destination. The metric is required for add commands. It must be
zero if the destination is on a directly-attached network, and nonzero if the route utilizes one or more gateways.
When adding a route with metric 0, the gateway given is the address of this host on the common network, indicating the interface to be used
for transmission. Routes to a particular host are distinguished from routes to a network by interpreting the Internet address associated
with destination. The optional keywords net and host force the destination to be interpreted as a network or host, respectively. If the
destination has a local address part of INADDR_ANY, then the route is assumed to be to a network. Otherwise, it is presumed to be a route
to a host. If the route is to a destination connected via a gateway, the metric should be greater than 0. All symbolic names specified
for a destination or gateway are looked up first as a host name using If this lookup fails, is then used to interpret the name as that of a
network.
The command uses a raw socket and the SIOCADDRT and SIOCDELRT ioctls to do its work. As such, only the superuser can modify the routing
tables.
Options
-f Flushes the routing tables of all gateway entries. If is used with one of the commands described above, the tables are flushed prior
to the command's application.
-n Prevents attempts to print host and network names symbolically when reporting actions.
Restrictions
The change operation is not implemented. Therefore, you should first add the new route, and then delete the old one.
Diagnostics
add [host | network] %s: gateway %s flags %x"
The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl call. If the
gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically as
well as symbolically.
delete [ host | network] %s: gateway %s flags %x
The specified route is being deleted from the tables. The values printed are from the routing table entry supplied in the ioctl call. If
the gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically
as well as symbolically.
%s %s done
When the flag is specified, each routing table entry that is deleted is indicated with a message of this form.
Network is unreachable
An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
not in table
A delete operation was attempted for an entry which was not present in the tables.
routing table overflow
An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
See Also
intro(4n), routed(8c)
route(8c)