09-21-2005
Still I got same bus error. The problem is that the dev is not at the address where keybuff + s_docname is
Some processors are not able to load an integer, unsigned etc, from an address which is not a multiple of the size of that integer. For 4-byte integers, the address it is loaded from, looking at the lowest two bit only, must be 00. It is called 4-byte alignment.
I need to "round up" my s_docname by some suitable calculation, leaving what is called 'padding' between docname and dev.
I need some advice on how to round this up. Thanks a lot.
10 More Discussions You Might Find Interesting
1. Solaris
Hi, I try to marshal a unsigned int and a char * into a buffer, and then unmarshal them later to get them out. I need to put the char * in the front and unsigned int at the end of the buffer. However, my system always give me "BUS ERROR". I am using Sun Sparcs Sloris 2.10.
My code to marshal the... (1 Reply)
Discussion started by: nj302
1 Replies
2. Programming
Hi All
I have a structure pointer and setting that pointer as NULL. When i tried to access the elements in the structure i am getting the error message.
"Cannot access memory at address 0x8". This i tried in LINUX.
When the same program is tried thro UNIX (HP-UX), i am not getting the message... (8 Replies)
Discussion started by: rkraj
8 Replies
3. Solaris
Hi,
The following error message occured when I was trying to reboot my SUN machine:
Memory address not aligned
Its a Sun 280 R , Ultra SPARC III
What should I do.
Varma (3 Replies)
Discussion started by: gunnervarma
3 Replies
4. Solaris
Hi,
Im working on Solaris 9 on SPARC-32 bit running on an Ultra-80, and I have to find out the following:-
1. Total Physical Memory in the system(total RAM).
2. Available Physical Memory(i.e. RAM Usage)
3. Total (Logical) Memory in the system
4. Available (Logical) Memory.
I know... (4 Replies)
Discussion started by: 0ktalmagik
4 Replies
5. Solaris
Is it possible to restrict physical memory in solaris zone with zone.max-locked-memory just like we can do with rcapd ? I do not want to used rcapd (1 Reply)
Discussion started by: fugitive
1 Replies
6. UNIX for Dummies Questions & Answers
hi,
For some special reason , I'd like to control the memory address for the shared libraries in my dynamically linked process.
And it is the "ld" which interpret the dynamically linked library, and in my system, the "ld-linux.so.2" is put at 0x00812000. Then I use "prelink -r" command to change... (0 Replies)
Discussion started by: zerocool_08
0 Replies
7. Linux
hi,
For some special reason , I'd like to control the memory address for the shared libraries in my dynamically linked process.
And it is the "ld" which interpret the dynamically linked library, and in my system, the "ld-linux.so.2" is put at 0x00812000. Then I use "prelink -r" command to... (3 Replies)
Discussion started by: zerocool_08
3 Replies
8. UNIX for Advanced & Expert Users
I want address of current virtual memory block?
i am using fedora10:wall::wall: (1 Reply)
Discussion started by: powyama
1 Replies
9. Solaris
Hi Experts,
Our servers running Solaris 10 with SAP Application. The memory utilization always >90%, but the process on SAP is too less even nothing.
Why memory utilization on solaris always looks high?
I have statement about memory on solaris, is this true:
Memory in solaris is used for... (4 Replies)
Discussion started by: edydsuranta
4 Replies
10. UNIX for Beginners Questions & Answers
How would I write a value to a physical memory address?
I was able to read a physical memory address (for example, 0x400) using this line:
dd if=/dev/mem count=4 bs=1 skip=$(( 0x400 ))
But I get an error:
dd: 'standard input': cannot skip to specified offset
when I try to write using... (1 Reply)
Discussion started by: rabrandt
1 Replies
LEARN ABOUT DEBIAN
brlapi__getdrivername
Getting Terminal information(3) BrlAPI Getting Terminal information(3)
NAME
Getting Terminal information -
How to get information about the connected Terminal.
Macros
#define BRLAPI_MAXNAMELENGTH 31
Functions
int BRLAPI_STDCALL brlapi_getDriverName (char *buffer, size_t size)
int BRLAPI_STDCALL brlapi__getDriverName (brlapi_handle_t *handle, char *buffer, size_t size)
int BRLAPI_STDCALL brlapi_getDisplaySize (unsigned int *x, unsigned int *y)
int BRLAPI_STDCALL brlapi__getDisplaySize (brlapi_handle_t *handle, unsigned int *x, unsigned int *y)
Detailed Description
Before using Raw mode or key codes, the application should always check the type of the connected terminal, to be sure it is really the one
it expects.
One should also check for display size, so as to adjust further displaying on it.
Macro Definition Documentation
#define BRLAPI_MAXNAMELENGTH 31
Maximum name length for names embeded in BrlAPI packets, not counting any termination character
Function Documentation
int BRLAPI_STDCALL brlapi__getDisplaySize (brlapi_handle_t *handle, unsigned int *x, unsigned int *y)
int BRLAPI_STDCALL brlapi__getDriverName (brlapi_handle_t *handle, char *buffer, size_tsize)
int BRLAPI_STDCALL brlapi_getDisplaySize (unsigned int *x, unsigned int *y)
Return the size of the braille display
int BRLAPI_STDCALL brlapi_getDriverName (char *buffer, size_tsize)
Return the complete name of the driver used by brltty
This function fills its argument with the whole name of the braille terminal if available, terminated with a '