Problem with N/W card in solaris Post: 8403

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS.

3. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

HI, I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors genunix: NOTICE: glm0: fault detected in device; service still unavailable genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported. Anyone has an idea, how to resolve...

4. SCO

LAN card problem

Dear all Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working. Is...

5. Solaris

emulex card on solaris 9

Hello, I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9). Who have already done this and can give me the procedure to follow ? driver to install multipath etc... Thanks in advance Emmanuel

6. Solaris

Network card drivers for solaris?

Hi all, i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig . during installation i was not requested for ip adddress even i plugged network cable. am i need to install any network card...

7. Solaris

Solaris 10 SCSI card question

I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance.

8. Solaris

Old RSC card problem

All, I have a unique situation concerning RSC cards and would like to see if anyone has a solution. Here is the situation: We are migrating older versions of Solaris using ufsdump images to like older hardware. We basically installed a temporary Solaris O/S then copied the dumps over and...

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

10. Solaris

Very new to Solaris and Sun, need help please (video card)

Hello all, I am trying to learn about Solaris and Sun systems so I purchased a SunFire 280r running Solaris 9 with a disk array from eBay. The system had no video card so I purchased a PGX32 card for the PCI slot and installed it. The problem is I have no video what so ever. I am familiar...

LEARN ABOUT CENTOS

enum_ieee80211_channel_flags

ENUM 
IEEE80211_CHANN(9) 					Device registration					   ENUM IEEE80211_CHANN(9)

NAME

       enum_ieee80211_channel_flags - channel flags

SYNOPSIS

       enum ieee80211_channel_flags {
	 IEEE80211_CHAN_DISABLED,
	 IEEE80211_CHAN_PASSIVE_SCAN,
	 IEEE80211_CHAN_NO_IBSS,
	 IEEE80211_CHAN_RADAR,
	 IEEE80211_CHAN_NO_HT40PLUS,
	 IEEE80211_CHAN_NO_HT40MINUS,
	 IEEE80211_CHAN_NO_OFDM,
	 IEEE80211_CHAN_NO_80MHZ,
	 IEEE80211_CHAN_NO_160MHZ
       };

CONSTANTS

       IEEE80211_CHAN_DISABLED
	   This channel is disabled.

       IEEE80211_CHAN_PASSIVE_SCAN
	   Only passive scanning is permitted on this channel.

       IEEE80211_CHAN_NO_IBSS
	   IBSS is not allowed on this channel.

       IEEE80211_CHAN_RADAR
	   Radar detection is required on this channel.

       IEEE80211_CHAN_NO_HT40PLUS
	   extension channel above this channel is not permitted.

       IEEE80211_CHAN_NO_HT40MINUS
	   extension channel below this channel is not permitted.

       IEEE80211_CHAN_NO_OFDM
	   OFDM is not allowed on this channel.

       IEEE80211_CHAN_NO_80MHZ
	   If the driver supports 80 MHz on the band, this flag indicates that an 80 MHz channel cannot use this channel as the control or any of
	   the secondary channels. This may be due to the driver or due to regulatory bandwidth restrictions.

       IEEE80211_CHAN_NO_160MHZ
	   If the driver supports 160 MHz on the band, this flag indicates that an 160 MHz channel cannot use this channel as the control or any
	   of the secondary channels. This may be due to the driver or due to regulatory bandwidth restrictions.

DESCRIPTION

       Channel flags set by the regulatory control code.

AUTHOR

       Johannes Berg <johannes@sipsolutions.net>
	   Author.

COPYRIGHT

Kernel Hackers Manual 3.10					     June 2014						   ENUM IEEE80211_CHANN(9)

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Discussion started by: i2admin

2. IP Networking

Solaris 9 Ethernet Card Problems

Discussion started by: saucierm

3. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

Discussion started by: s_aamir

4. SCO

LAN card problem

Discussion started by: ccvyas