10-11-2001
hi optimus
thks for suggestions .. is it behaving due to the mismatch in the driver or due to any other reason??..
Regds
Francis
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
4. SCO
Dear all
Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working.
Is... (1 Reply)
Discussion started by: ccvyas
1 Replies
5. Solaris
Hello,
I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9).
Who have already done this and can give me the procedure to follow ?
driver to install
multipath
etc...
Thanks in advance
Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies
6. Solaris
Hi all,
i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig .
during installation i was not requested for ip adddress even i plugged network cable.
am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies
7. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
8. Solaris
All,
I have a unique situation concerning RSC cards and would like to see if anyone has a solution. Here is the situation:
We are migrating older versions of Solaris using ufsdump images to like older hardware. We basically installed a temporary Solaris O/S then copied the dumps over and... (5 Replies)
Discussion started by: sljack
5 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Solaris
Hello all,
I am trying to learn about Solaris and Sun systems so I purchased a SunFire 280r running Solaris 9 with a disk array from eBay. The system had no video card so I purchased a PGX32 card for the PCI slot and installed it.
The problem is I have no video what so ever. I am familiar... (3 Replies)
Discussion started by: FTBTX
3 Replies
AHB(4) BSD Kernel Interfaces Manual AHB(4)
NAME
ahb -- Adaptec EISA SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ahb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ahb_load="YES"
DESCRIPTION
This driver provides access to the SCSI bus connected to an Adaptec AHA-174X host adapters in ``enhanced'' mode. Tagged queueing and syn-
chronous SCSI transfers are supported.
HARDWARE
The ahb driver supports the following SCSI host adapters:
o Adaptec AHA-1740
o Adaptec AHA-1742
o Adaptec AHA-1740A
o Adaptec AHA-1742A
CAVEATS
The Adaptec 174X is very sensitive to SCSI bus termination and cable length. It may also have difficulties operating with some modern
devices that, due to their speed, expose timing problems in the controller. There are no known mechanisms for working around device incom-
patibilities of this nature.
SEE ALSO
aha(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)
AUTHORS
The ahb driver was written by Justin T. Gibbs.
BSD
July 4, 2004 BSD