09-20-2005
They will be fine in slots 7 and 8, the card in question is dual voltage, it's the QLogic QLA2200F/66-SUN 3.3/5V 32/64Bit 33/66MHz and will work in any of the slots in an 880.
10 More Discussions You Might Find Interesting
1. BSD
Hi!
I just wanted to know what network cards are supported in FreeBSD. I have looked at the list of supported cards but I can't find any of them in the stores. Is the list not updated, I would really preciate info about where (in EU, Sweden) I can buy them.
/Peter (2 Replies)
Discussion started by: Barfly.se
2 Replies
2. AIX
I am trying to find PCI Ethernet cards that are compatible with the IBM RISC 6000 - B50 Power PC. None of the regular NIC's seem to have AIX drivers. Does anyone know of AIX drivers for standard PCI Ethernet NIC's or a non IBM NIC that works with the Model B50 at 10/100 MB ? (0 Replies)
Discussion started by: rahe
0 Replies
3. Solaris
Has anyone ever relocated an HBA card after already having it configured in another PCI slot? I've found that the HBA instance #'s start incrementing past the previous. It results in me having to have my instance numbers in /kernel/drv/qla2300.conf be 4,5,6,7 instead of 0,1,2,3. Cleanup with... (5 Replies)
Discussion started by: kduffin
5 Replies
4. Solaris
We have 3 V880's and we need to purchase a KVM for them. I've never purchased one before. Does anyone have a recommendation for one? (3 Replies)
Discussion started by: dangral
3 Replies
5. Solaris
I have two mechine, one is SUN V880 and another is IBM p570.
I run the same script on V880 and p570 , why the cpu usage always under 50% on V880 but the cpu usage can growth to 100% on p570. (4 Replies)
Discussion started by: golden
4 Replies
6. Solaris
Hi,
I'mtrying to connect a Device via the serial port to my Solaris 10 environment (Sunfire V880).
I have setup ttyb to connect to the Device. I am getting a connected status in my Port Listing (Using a separate Module that I have in the app running in the environment) but the moment I try to... (0 Replies)
Discussion started by: Alchemist
0 Replies
7. Solaris
Hello All,
I am not a sun expert, but in my network administration job I had to deal with SUN servers. We've to replace a faulty motherboard of SF V880. As per my understanding, host id of machines is programmed in PROM. So will host ID be changed with the replacement of V880 motherboard?... (6 Replies)
Discussion started by: Charagh
6 Replies
8. Solaris
Any help on this would be greatly appreciated. I have read other threads on similar subject but still not clear on what this is telling me and what action to take. Do I have a couple of disks that are slowly dying?
While checking disk usage on the V880 I noticed the following:
# format... (3 Replies)
Discussion started by: jamba1
3 Replies
9. Solaris
Hi
I have a 1TB external drive that I want to attach to a SunFire v880 server which runs on Solaris 9. After attaching the external drive what commands should I issue so that the drive will be seen by the server? (7 Replies)
Discussion started by: rahmantanko
7 Replies
10. Hardware
Hi
Does someone have the latest firmware for a sunfire v880
I have a problem with the FC-AL disk i guess i need to upgrade the firmware but i dont have a support with oracle and i can't find it anywhere
thank you (4 Replies)
Discussion started by: simplextibi
4 Replies
DPT(4) BSD Kernel Interfaces Manual DPT(4)
NAME
dpt -- DPT RAID Controller SCSI driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device dpt
For one or more EISA cards:
device eisa
For one or more ISA cards:
device isa
For one or more PCI cards:
device pci
To allow PCI adapters to use memory mapped I/O if enabled:
options DPT_ALLOW_MEMIO
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
dpt_load="YES"
DESCRIPTION
The dpt driver supports DPT RAID SCSI controllers.
SmartRAID (PM3???) are "Enterprise" class cards, and SmartCache (PM2???) cards are in the "Workstation" class. The Gen 4 Smart Cache IV
products were a re-issue of the Gen 3 utilizing upgraded (and cheaper to produce) silicon. The PM3334 (Smart RAID III) was not revamped as
there was no upgraded silicon (68040 processor) and it was using the best DPT made. Note there has been customer confusion over the faster
enterprise class card supported by this driver being an older generation. The Gen5 cards are supported by the asr(4) driver.
HARDWARE
The dpt driver provides support for the following RAID adapters:
o DPT Smart Cache Plus
o Smart Cache II (PM2?2?, PM2022 [EISA], PM2024/PM2124 [PCI]) (Gen2)
o Smart RAID II (PM3?2?, PM3021, PM3222)
o Smart Cache III (PM2?3?)
o Smart RAID III (PM3?3?, PM3332 [EISA], PM3334UW [PCI]) (Gen3)
o Smart Cache IV (PM2?4?, PM2042 [EISA], PM2044/PM2144 [PCI]) (Gen4)
o Smart RAID IV
SEE ALSO
asr(4), cd(4), ch(4), da(4), sa(4), scsi(4)
HISTORY
The dpt driver first appeared in FreeBSD 2.2.6.
AUTHORS
The dpt driver was written by Simon Shapiro and ported to the CAM SCSI system by Justin T. Gibbs.
BSD
June 18, 2006 BSD