10-09-2001
Thankyou for the tips. The drive was supplied by a reseller so I hope :-) that it isn't broken. Following conversations of this problem on USENET it has been suggested that the Ultra-SCSI interface of this drive is not compatiable with the HP6000-SE enclosure, the SE standing for "single ended".
Thanks for you help.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed a new SCSI drive into an HP6000-SE SCSI tower conencted to an old HP9000. This device cannot be detected by SAM. HOWEVER, when doing an ioscan -f I get:
======================================================================
bc 0 ... (2 Replies)
Discussion started by: sam_pointer
2 Replies
2. Filesystems, Disks and Memory
I need more space on my Ultra 10, and was thinking of a pair of 60 or 80 GB 7200 rpm ATA/100 drives mirrored with DiskSuite. Will afterarket IDE drives work in the Sun box? Are there any issues? (1 Reply)
Discussion started by: 98_1LE
1 Replies
3. Filesystems, Disks and Memory
I am looking for a Disk Drive for SGI Octane with Irix 6.4 .
I was just hoping if someone out there can give me the
vendor and part number ... Need a 9GB hopefully. (1 Reply)
Discussion started by: DPAI
1 Replies
4. Filesystems, Disks and Memory
Pointing one hard drive name to another disk
--------------------------------------------------------------------------------
I have 2 disk drives - s2d9 & s2d11 on a solaris Unix system
It was mapped so that anything that tried to call s2d9 would be pointed to s2d11 since s2d9 was bad.... (2 Replies)
Discussion started by: andy57s
2 Replies
5. HP-UX
I thought I would post it again..once a bad drive is replaced need to rebuild it right?? Is disk and drive same? So what command need when the disk gets replaces. When i did diskinfo...and found out the bad disk...and need to replace that..
Thanks if someone could answer this question i have. (1 Reply)
Discussion started by: catwomen
1 Replies
6. UNIX for Advanced & Expert Users
Any creative ideas on how to wreck / secure clean an hard disk drive before disposal?
dd if=/dev/zero of=/dev/disk_drive?
shred -n whatever -z /dev/disk_drive?
Magnet? (false sense of security)
Fire?
Hammer?
Acid?
Post your thoughts. (10 Replies)
Discussion started by: redoubtable
10 Replies
7. Solaris
Hi,
What are the initial checks needs to be done while observing hard errors on one of the hard disk drive.
Thanks,
Babu. (1 Reply)
Discussion started by: lbreddy
1 Replies
8. UNIX for Dummies Questions & Answers
Hello,
This is my first post :)
I wondered if it would be possible to connect a unix machine via USB as a disk drive in the same way as Android devices connects to the computers.
The idea is to connect my debian machine to the television, that is compatible with USB pendrives. Then, the... (3 Replies)
Discussion started by: Strife
3 Replies
9. UNIX for Advanced & Expert Users
Hi Team
when I boot the server I get this 2 errors :
the disk drive for /tmp is not ready yet or not present
the disk drive for /boot is not ready yet or not present
and its stay like that , I m using Ubuntu 12.04
please if someone have any idea how to fix that problem . (1 Reply)
Discussion started by: SULTAN01
1 Replies
SD(4) Linux Programmer's Manual SD(4)
NAME
sd - driver for SCSI disk drives
SYNOPSIS
#include <linux/hdreg.h> /* for HDIO_GETGEO */
#include <linux/fs.h> /* for BLKGETSIZE and BLKRRPART */
CONFIGURATION
The block device name has the following form: sdlp, where l is a letter denoting the physical drive, and p is a number denoting the parti-
tion on that physical drive. Often, the partition number, p, will be left off when the device corresponds to the whole drive.
SCSI disks have a major device number of 8, and a minor device number of the form (16 * drive_number) + partition_number, where drive_num-
ber is the number of the physical drive in order of detection, and partition_number is as follows:
+3 partition 0 is the whole drive
partitions 1-4 are the DOS "primary" partitions
partitions 5-8 are the DOS "extended" (or "logical") partitions
For example, /dev/sda will have major 8, minor 0, and will refer to all of the first SCSI drive in the system; and /dev/sdb3 will have
major 8, minor 19, and will refer to the third DOS "primary" partition on the second SCSI drive in the system.
At this time, only block devices are provided. Raw devices have not yet been implemented.
DESCRIPTION
The following ioctls are provided:
HDIO_GETGEO
Returns the BIOS disk parameters in the following structure:
struct hd_geometry {
unsigned char heads;
unsigned char sectors;
unsigned short cylinders;
unsigned long start;
};
A pointer to this structure is passed as the ioctl(2) parameter.
The information returned in the parameter is the disk geometry of the drive as understood by DOS! This geometry is not the physical
geometry of the drive. It is used when constructing the drive's partition table, however, and is needed for convenient operation of
fdisk(1), efdisk(1), and lilo(1). If the geometry information is not available, zero will be returned for all of the parameters.
BLKGETSIZE
Returns the device size in sectors. The ioctl(2) parameter should be a pointer to a long.
BLKRRPART
Forces a reread of the SCSI disk partition tables. No parameter is needed.
The SCSI ioctl(2) operations are also supported. If the ioctl(2) parameter is required, and it is NULL, then ioctl(2) fails with
the error EINVAL.
FILES
/dev/sd[a-h]
the whole device
/dev/sd[a-h][0-8]
individual block partitions
COLOPHON
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the
latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.
Linux 2017-09-15 SD(4)