08-29-2005
My inclination would be to say that you have either a routing, or more likely a name resoluation issue, but it could also be that you have an auto-negotiation problem.
Check your nsswitch.conf, resolv.conf and routing information. If you can find nothing wrong there, try forcing autonegotiation, by using ndd to set the tunable adv_autoneg_cap to 1 for your network interface.
10 More Discussions You Might Find Interesting
1. BSD
just as the title says.
thanks.
#General Rule Sets
/sbin/ipfw add 0300 check-state
/sbin/ipfw add 0301 deny tcp from any to any in established
/sbin/ipfw add 0302 pass tcp from any to any out setup keep-state
/sbin/ipfw add 0303 pass udp from any to any out
#SSH FTP
/sbin/ipfw add 0400... (11 Replies)
Discussion started by: dwildgoose
11 Replies
2. UNIX for Dummies Questions & Answers
SCO Unix 5.0.5 moving to Red Hat
Intel EtherExpress Pro/100+
Newbie that just started working for a company and having an issue with transfer speeds over the network. Need to move 1.5GB of data from an old server with a single SCSI HDD to a new server with RAID 5 SATA HDD's. Goal was to FTP... (4 Replies)
Discussion started by: rockboles
4 Replies
3. UNIX for Dummies Questions & Answers
Hi again guys,
Earlier today, just all of a sudden, all SSH and FTP connections to my internal Linux box just slowed down to a crawl. After the connection/authentication though, everything was back to normal speed. Until you have to connect again. A box reboot didnt work either.
Now, from... (1 Reply)
Discussion started by: Aeros
1 Replies
4. UNIX for Dummies Questions & Answers
Running open solaris on a e420 that I recently picked up. Having issues sshing to it from either of my Linux boxes as its very slow to login (from the solaris box to the linux box it connects just fine.
Here is the output of ssh -vvv. I have hightlighted where it seems the slowdown is. Does... (0 Replies)
Discussion started by: creedog
0 Replies
5. UNIX for Dummies Questions & Answers
Folks;
Is there a way in UNIX to do the following:
When users use FTP to login to a mounted drive on Solaris server, if that was their first time login a home directory for that user will be created & if the home directory exists it won't create a home directory (user should not have a login... (6 Replies)
Discussion started by: Katkota
6 Replies
6. Solaris
Hi Guys and Girls, I know this is a common question but I've searched and we've tried the suggestions without luck. When I log into the box via SSH from a windows machine I get a 1 min 20 sec delay. If we add my IP address and machine name to /etc/hosts then I get an instant login. I would be happy... (12 Replies)
Discussion started by: MikeKulls
12 Replies
7. Shell Programming and Scripting
I have some sample code that's supposed to ssh to another machine using Net::SSH::Perl, execute a command, and print
the output of that command. It's very basic, and it works. However, I noticed that upon logging in:
$ssh->login('username','password');
It takes roughly 10-13 seconds to... (2 Replies)
Discussion started by: mrwatkin
2 Replies
8. Solaris
Hi, I have the following issue, when I tried to login to an Openindiana remote server through ssh It takes to long to ask me for the password. So i tried -v and I realize that sshd hangs here " debug1: SSH2_MSG_SERVICE_ACCEPT received " for at least 2 minutes. Then I can log in and everything is... (2 Replies)
Discussion started by: piukeman
2 Replies
9. UNIX for Advanced & Expert Users
Version: Oracle Enterprise Linux 6.3
Running on VMWare Workstation
When I login to my Linux VM from putty, the third line prompting for password comes only after few seconds.
login as: root
Access denied
root@192.168.0.235's password: ---> It takes around 5 seconds to get this prompt
I... (1 Reply)
Discussion started by: John K
1 Replies
10. Solaris
ssh is slow on solaris zone , and is getting stuck at the following place.
debug2: callback done
debug2: channel 0: open confirm rwindow 0 rmax 32768
debug3: Wrote 664 bytes for a total of 3325
Below is the ssh version being used: Sun_SSH_1.1.6, SSH protocols 1.5/2.0, OpenSSL 0x0090704f
... (10 Replies)
Discussion started by: skamal4u
10 Replies
netrc(5) File Formats Manual netrc(5)
Name
netrc - file used by ftp auto-login procedure (.netrc)
Description
The file contains frequently needed options for transfers. The file resides in the owner's home directory on the machine from which the
owner initiates the file transfer. If the file includes passwords, set permissions on the file with so that only the owner has read per-
mission.
The file uses the following format:
o Each line of the file defines options for a specific machine.
o A line in the file can be either a machine line or a default line.
o The default line must be the first line in the file if it is present.
o Fields in a default line appear in this order: default, default machine name.
o Fields in a machine line appear in this order: machine, machine name, options.
o Fields on each line are separated by spaces or tabs.
The following are valid options for a machine line:
-------------------------------------------------------------------
Option Parameter Default Description
-------------------------------------------------------------------
machine machine name none Identifies a remote
machine name
login name local name Identifies user on the
remote machine
password password none Password for remote
login name
account password none Additional account password
macdef macro name none Defines a macro like the
ftp macdef command
-------------------------------------------------------------------
Example
This is an example of a file:
machine cactus login smith
machine nic.ddn.mil login anonymous password anonymous
machine palm.stateu.edu login smith password ualonerwelcome
macdef byenow
quit
macdef ls
dir
The first line allows to log Smith into the machine after prompting for and receiving Smith's password, as shown in this example:
$ ftp cactus
Connected to cactus.tech.edu
FTP server ready.
Password required for SMITH.
User logged in
ftp>
The second line of the file allows the user to perform an anonymous transfer after typing this command:
$ ftp nic.ddn.mil
See for a description of anonymous FTP transfers.
The third line allows Smith to log into the machine Smith will not be prompted for a password because this machine line includes password
information. Because the file includes password information, the file must not have read permission set for world and group.
The lines are macro definitions, which operate much like shell aliases. A blank line must follow each macro definition to signal the end
of the macro. The first macro definition defines as an alias for the command.
See Also
ftp(1c)
netrc(5)