Sponsored Content
Operating Systems Solaris Solaris 9 slow login thru ssh & ftp Post 82216 by reborg on Monday 29th of August 2005 05:08:47 PM
Old 08-29-2005
My inclination would be to say that you have either a routing, or more likely a name resoluation issue, but it could also be that you have an auto-negotiation problem.

Check your nsswitch.conf, resolv.conf and routing information. If you can find nothing wrong there, try forcing autonegotiation, by using ndd to set the tunable adv_autoneg_cap to 1 for your network interface.
 

10 More Discussions You Might Find Interesting

1. BSD

ipfw slow ssh and ftp connections

just as the title says. thanks. #General Rule Sets /sbin/ipfw add 0300 check-state /sbin/ipfw add 0301 deny tcp from any to any in established /sbin/ipfw add 0302 pass tcp from any to any out setup keep-state /sbin/ipfw add 0303 pass udp from any to any out #SSH FTP /sbin/ipfw add 0400... (11 Replies)
Discussion started by: dwildgoose
11 Replies

2. UNIX for Dummies Questions & Answers

Slow FTP & SMB

SCO Unix 5.0.5 moving to Red Hat Intel EtherExpress Pro/100+ Newbie that just started working for a company and having an issue with transfer speeds over the network. Need to move 1.5GB of data from an old server with a single SCSI HDD to a new server with RAID 5 SATA HDD's. Goal was to FTP... (4 Replies)
Discussion started by: rockboles
4 Replies

3. UNIX for Dummies Questions & Answers

SSH and FTP connect slow

Hi again guys, Earlier today, just all of a sudden, all SSH and FTP connections to my internal Linux box just slowed down to a crawl. After the connection/authentication though, everything was back to normal speed. Until you have to connect again. A box reboot didnt work either. Now, from... (1 Reply)
Discussion started by: Aeros
1 Replies

4. UNIX for Dummies Questions & Answers

Painfully Slow SSH login on Solaris box

Running open solaris on a e420 that I recently picked up. Having issues sshing to it from either of my Linux boxes as its very slow to login (from the solaris box to the linux box it connects just fine. Here is the output of ssh -vvv. I have hightlighted where it seems the slowdown is. Does... (0 Replies)
Discussion started by: creedog
0 Replies

5. UNIX for Dummies Questions & Answers

FTP & login

Folks; Is there a way in UNIX to do the following: When users use FTP to login to a mounted drive on Solaris server, if that was their first time login a home directory for that user will be created & if the home directory exists it won't create a home directory (user should not have a login... (6 Replies)
Discussion started by: Katkota
6 Replies

6. Solaris

Slow login via SSH

Hi Guys and Girls, I know this is a common question but I've searched and we've tried the suggestions without luck. When I log into the box via SSH from a windows machine I get a 1 min 20 sec delay. If we add my IP address and machine name to /etc/hosts then I get an instant login. I would be happy... (12 Replies)
Discussion started by: MikeKulls
12 Replies

7. Shell Programming and Scripting

Net::SSH::Perl slow to login.

I have some sample code that's supposed to ssh to another machine using Net::SSH::Perl, execute a command, and print the output of that command. It's very basic, and it works. However, I noticed that upon logging in: $ssh->login('username','password'); It takes roughly 10-13 seconds to... (2 Replies)
Discussion started by: mrwatkin
2 Replies

8. Solaris

Open Indiana 151a - Slow SSH Login

Hi, I have the following issue, when I tried to login to an Openindiana remote server through ssh It takes to long to ask me for the password. So i tried -v and I realize that sshd hangs here " debug1: SSH2_MSG_SERVICE_ACCEPT received " for at least 2 minutes. Then I can log in and everything is... (2 Replies)
Discussion started by: piukeman
2 Replies

9. UNIX for Advanced & Expert Users

OEL 6.3 :Slow login due to /etc/ssh/sshd_config configuration

Version: Oracle Enterprise Linux 6.3 Running on VMWare Workstation When I login to my Linux VM from putty, the third line prompting for password comes only after few seconds. login as: root Access denied root@192.168.0.235's password: ---> It takes around 5 seconds to get this prompt I... (1 Reply)
Discussion started by: John K
1 Replies

10. Solaris

Slow ssh on Solaris 10 zone

ssh is slow on solaris zone , and is getting stuck at the following place. debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug3: Wrote 664 bytes for a total of 3325 Below is the ssh version being used: Sun_SSH_1.1.6, SSH protocols 1.5/2.0, OpenSSL 0x0090704f ... (10 Replies)
Discussion started by: skamal4u
10 Replies
DNROUTE(8)						      System Manager's Manual							DNROUTE(8)

NAME
dnroute - DECnet Routing Daemon SYNOPSIS
dnroute [options] Options: [-dvV2Dtnhr] DESCRIPTION
dnroute is a daemon that manages the DECnet routing tables to provide a simple but probably useful routing policy. dnroute listens for incoming routing messages and adds routes in the kernel for non-local areas that it sees. Routes will be modifed according to these messages so that the lowest cost route that is up will always be used. Routes to locally accessible nodes (it those in the neighbour table) will also be added. If you want to keep manual control of the route to a particular area, then add a line into dnroute.conf. eg: manual 26 will disable dnroute's setting of routing tables for that area. dnetinfo will still show the route that would have been set with (M) on the line to show it has been overidden. To implement its routing policies dnroute assumes that all interfaces on the system have a cost of 4. To change this add lines in /etc/dnroute.conf for each of the interfaces you need to change. eg eth0 6 eth1 8 tap0 10 A script called dnetinfo is provided that gets the routing information from dnroute and displays it on stdout in a format similar to the VMS command SHOW NET/OLD. OPTIONS
-d Don't fork and run the background. Use this for debugging. -v Verbose. Log route changes to syslog. -D Debug log. Writes debugging information to stderr. Only useful with -d. -h -? Displays help for using the command. -r Send DECnet routing messages showing the state of local nodes. -2 Send DECnet level 2 (area) routing messages. Implies -r. -t <secs> Timer to send routing messages on. Defaults to 15 seconds. -n Do not set up routes or send routing messages, just monitor the network. Useful for testing. -V Show the version of dnroute. SEE ALSO
dnetd.conf(5), ip(8) DECnet utilities March 30 2006 DNROUTE(8)
All times are GMT -4. The time now is 06:58 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy