10-08-2001
If it is an "old HP9000", it may not support your disk drive. There are patches to various HP-UX releases that include support for various drives. You will need to search to patches for your release of HP-UX to be sure that you are at the right patch level to use the drive.
Another thought is that the drive may be broken. See if the diskinfo command can report on the drive.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed a new SCSI drive into an HP6000-SE SCSI tower conencted to an old HP9000. This device cannot be detected by SAM. HOWEVER, when doing an ioscan -f I get:
======================================================================
bc 0 ... (2 Replies)
Discussion started by: sam_pointer
2 Replies
2. Filesystems, Disks and Memory
I need more space on my Ultra 10, and was thinking of a pair of 60 or 80 GB 7200 rpm ATA/100 drives mirrored with DiskSuite. Will afterarket IDE drives work in the Sun box? Are there any issues? (1 Reply)
Discussion started by: 98_1LE
1 Replies
3. Filesystems, Disks and Memory
I am looking for a Disk Drive for SGI Octane with Irix 6.4 .
I was just hoping if someone out there can give me the
vendor and part number ... Need a 9GB hopefully. (1 Reply)
Discussion started by: DPAI
1 Replies
4. Filesystems, Disks and Memory
Pointing one hard drive name to another disk
--------------------------------------------------------------------------------
I have 2 disk drives - s2d9 & s2d11 on a solaris Unix system
It was mapped so that anything that tried to call s2d9 would be pointed to s2d11 since s2d9 was bad.... (2 Replies)
Discussion started by: andy57s
2 Replies
5. HP-UX
I thought I would post it again..once a bad drive is replaced need to rebuild it right?? Is disk and drive same? So what command need when the disk gets replaces. When i did diskinfo...and found out the bad disk...and need to replace that..
Thanks if someone could answer this question i have. (1 Reply)
Discussion started by: catwomen
1 Replies
6. UNIX for Advanced & Expert Users
Any creative ideas on how to wreck / secure clean an hard disk drive before disposal?
dd if=/dev/zero of=/dev/disk_drive?
shred -n whatever -z /dev/disk_drive?
Magnet? (false sense of security)
Fire?
Hammer?
Acid?
Post your thoughts. (10 Replies)
Discussion started by: redoubtable
10 Replies
7. Solaris
Hi,
What are the initial checks needs to be done while observing hard errors on one of the hard disk drive.
Thanks,
Babu. (1 Reply)
Discussion started by: lbreddy
1 Replies
8. UNIX for Dummies Questions & Answers
Hello,
This is my first post :)
I wondered if it would be possible to connect a unix machine via USB as a disk drive in the same way as Android devices connects to the computers.
The idea is to connect my debian machine to the television, that is compatible with USB pendrives. Then, the... (3 Replies)
Discussion started by: Strife
3 Replies
9. UNIX for Advanced & Expert Users
Hi Team
when I boot the server I get this 2 errors :
the disk drive for /tmp is not ready yet or not present
the disk drive for /boot is not ready yet or not present
and its stay like that , I m using Ubuntu 12.04
please if someone have any idea how to fix that problem . (1 Reply)
Discussion started by: SULTAN01
1 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
chown(1), mknod(1), sd(4), mount(8)
COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)