08-10-2005
hi ...
if you are the superuser .. check with command
>sar 3 3 (SAR should be installed)
there is one more command which will give full statistics of various thing .. but remember this is a dynamic command and keeps running till you cancel it using ctrl-C
>topas
do let me know if it helps
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
What command do you use to verify if the CPU utilization. Example. If the CPU is at 98%?
Thanks (4 Replies)
Discussion started by: kimosilk
4 Replies
2. UNIX for Advanced & Expert Users
On user complains about the performance of web application, as a part application support, we use following commands to see the CPU utilization in the UNIX using ‘sar' command. Some times it goes below 20 and even reaches 0.
HLW$~> sar -u 10 60
SunOS HLW 5.8 Generic_117350-14 sun4u ... (2 Replies)
Discussion started by: thinakarmani
2 Replies
3. UNIX for Dummies Questions & Answers
Hi, iam new to AIX and had a basic question.
I was asked to give a chart of CPU utilization in percentage for every hour.
where can i look for information and which column should i look at?
I would be very thankful if somebody could respond.
Thanks!
karthik (1 Reply)
Discussion started by: karthikosu
1 Replies
4. Shell Programming and Scripting
Hi to All,
Would you please help me.
I would like to know, In Unix How to know CPU utilization for every process.
Thanks in Advance.
Thanks,
Divyang (3 Replies)
Discussion started by: div_Neev
3 Replies
5. UNIX for Dummies Questions & Answers
hi,
i want to know cpu utilizatiion per process per cpu..for single processor also if multicore in linux ..to use these values in shell script to kill processes exceeding cpu utilization.ps (pcpu) command does not give exact values..top does not give persistant values..psstat,vmstat..does njot... (3 Replies)
Discussion started by: pankajd
3 Replies
6. Shell Programming and Scripting
Hi all,
I found like top command could be used to find the Memory and CPU utilization. But i want to know how to find the Memory and CPU utilization for a particular user using top command.
Thanks in advance.
Thanks,
Ananthi.U (2 Replies)
Discussion started by: ananthi_ku
2 Replies
7. AIX
Hi All,
Can some one help me in finding % CPU Utilization ?
From VMSTAT command, How we can find % utilization ?
Thanks (3 Replies)
Discussion started by: VBudatha
3 Replies
8. UNIX for Advanced & Expert Users
Hi,
any commande on AIX 6.1 that shows me total CPU utilization ?
I saw curt in documentation but there should be a trace file before.
Thank you. (1 Reply)
Discussion started by: big123456
1 Replies
9. AIX
Could you please explain about calculate CPU utilization of aix server using lparstat command?
Here below i have provided example output from aix test server.
System configuration: type=Shared mode=Uncapped smt=On lcpu=4 mem=4096 psize=63 ent=0.50
%user %sys %wait %idle physc %entc ... (1 Reply)
Discussion started by: maruthu
1 Replies
10. Red Hat
Hi,
i am new to linux/RHEL 6.0 and i have two questions.
1) How to get the CPU utilization and Memory Utilization of all Services running currently?
2) How to get the CPU utilization and Memory Utilization of all Applications running currently?
Please help me to find the script.
... (2 Replies)
Discussion started by: nossam
2 Replies
LEARN ABOUT DEBIAN
fiu-ctrl
fiu-ctrl(1) General Commands Manual fiu-ctrl(1)
NAME
fiu-ctrl - a script to remote control programs using libfiu
SYNOPSIS
fiu-ctrl [options] PID [PID ...]
DESCRIPTION
fiu-ctrl is a script to enable/disable failure points in running programs that are using libfiu(3).
Programs are usually launched using fiu-run(1), which enables libfiu's remote control capabilities without the need to modify the program's
code.
For additional documentation, go to the project's website at http://blitiri.com.ar/p/libfiu.
OPTIONS
-c command
Run the given libfiu remote control command before executing the program (see below for reference).
-f ctrlpath
Set the default prefix for remote control over named pipes. Defaults to "$TMPDIR/fiu-ctrl", or "/tmp/fiu-ctrl" if "$TMPDIR" is not
set, which is the usually correct for programs launched using fiu-run(1).
Remote control commands are of the form "command param1=value1,param2=value2". Valid commands are:
'enable name=NAME'
Enables the NAME failure point unconditionally.
'enable_random name=NAME,probability=P'
Enables the NAME failure point with a probability of P.
'disable name=NAME'
Disables the NAME failure point.
All of the enable* commands can also optionally take failnum and failinfo parameters, analogous to the ones taken by the C functions.
EXAMPLES
The following command will tell the process running with PID 12345 to enable the failure point posix/io/read with a 25% of probability to
fail, and the failure point libc/mm/malloc with a 5% of probability to fail:
fiu-ctrl -c 'enable_random name=posix/io/*,probability=0.25'
-c 'enable_random name=libc/mm/*,probability=0.05' 12345
And the following will tell the same process to disable the previously enabled failure point posix/io/read:
fiu-ctrl -c 'disable name=posix/io/read' 12345
SEE ALSO
libfiu(3), fiu-run(1).
BUGS
If you want to report bugs, or have any questions or comments, just let me know at albertito@blitiri.com.ar. For more information about
libfiu, you can go to http://blitiri.com.ar/p/libfiu.
16/Jun/2009 fiu-ctrl(1)