08-02-2005
Hi expert,
Thks for the feedback..
I have tried to remove the hostname.hme0 in the etc directory, but still recieving the link down error messages. Maybe i will check with the application team whether any application configured using hme0 previously..
10 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT HPUX
remove_directory
remove directory(1m) remove directory(1m)
NAME
remove directory - Removes a value from a set-valued or single-valued attribute (including application-defined attributes) of a directory
SYNOPSIS
cdscp remove directory directory-name attribute-name [= attribute-value]
ARGUMENTS
The full name of the directory. The name of a particular attribute. Specify only one attribute at a time. See the cds_attributes file
for the list of attributes and corresponding data types that your application uses. The value of a particular attribute. The value of an
application-defined attribute is dependent on the type of attribute.
DESCRIPTION
The remove directory command removes a value from a set-valued or single-valued attribute (including application-defined attributes) of a
directory. If you do not specify a value, the command removes the entire attribute. This command can delete attributes created by the add
directory and set directory commands. Usually this task is performed through the client application. See the OSF DCE Administration Guide
for more information about attributes.
Privilege Required
You must have write permission to the directory.
NOTE
This command is replaced at Revision 1.1 by the dcecp command and may not be provided in future releases of DCE.
EXAMPLE
To remove the value 1 from the user-defined, set-valued attribute dirregion of a directory named /.:/sales, follow these steps: Read the
cds_attributes file to check that the attribute dirregion is listed, as shown in the following display:
OID LABEL SYNTAX 1.3.22.1.3.66 dirregion small Enter the following command to remove the value 1 from the
attribute dirregion. cdscp> remove directory /.:/sales dirregion = 1
RELATED INFORMATION
Commands: add directory(1m), list directory(1m), set directory(1m), set directory to skulk(1m), show directory(1m)
Books: OSF DCE Administration Guide
remove directory(1m)