|
|
Sponsored Content
Top Forums
UNIX for Advanced & Expert Users
network interface problem
Post 79951 by amit_sapre on Tuesday 2nd of August 2005 10:28:10 AM
08-02-2005
I feel the easiest way to disable hme0 network interface is :-
1. Rename the file /etc/hostname.hme0 to something else (or delete that file)
2. Reboot the system.
This ensures that hme0 interface is not configured on rebooting...
Hope this solves the problem...
1. Rename the file /etc/hostname.hme0 to something else (or delete that file)
2. Reboot the system.
This ensures that hme0 interface is not configured on rebooting...
Hope this solves the problem...
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT MOJAVE
systemd-networkd-wait-online.service
SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8) systemd-networkd.service SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8) NAME
systemd-networkd-wait-online.service, systemd-networkd-wait-online - Wait for network to come online SYNOPSIS
systemd-networkd-wait-online.service /lib/systemd/systemd-networkd-wait-online DESCRIPTION
systemd-networkd-wait-online is a one-shot system service that waits for the network to be configured. By default, it will wait for all links it is aware of and which are managed by systemd-networkd.service(8) to be fully configured or failed, and for at least one link to gain a carrier. OPTIONS
The following options are understood: -i, --interface= Network interface to wait for before deciding if the system is online. This is useful when a system has several interfaces which will be configured, but a particular one is necessary to access some network resources. This option may be used more than once to wait for multiple network interfaces. When used, all other interfaces are ignored. --ignore= Network interfaces to be ignored when deciding if the system is online. By default, only the loopback interface is ignored. This option may be used more than once to ignore multiple network interfaces. --timeout= Fail the service if the network is not online by the time the timeout elapses. A timeout of 0 disables the timeout. Defaults to 120 seconds. SEE ALSO
systemd(1), systemd-networkd.service(8) systemd 237 SYSTEMD-NETWORKD-WAIT-ONLINE.SERVICE(8)