08-01-2005
have you removed it or just unconfigured your hme0 interface? see man ifconfig:
# ifconfig hme0 unplumb <-- will remove hme0 from your system
gP
10 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT SUNOS
inet_type
inet_type(4) File Formats inet_type(4)
NAME
inet_type - default Internet protocol type
SYNOPSIS
/etc/default/inet_type
DESCRIPTION
The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.
The inet_type file can contain a number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.
The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file. By default,
both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
setting the value of DEFAULT_IP. The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
will be displayed:
IP_VERSION4 Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
and netstat(1M) commands.
IP_VERSION6 Displays both IPv4 and IPv6 related information for ifconfig and netstat.
BOTH Displays both IPv4 and IPv6 related information for ifconfig and netstat.
The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For example,
even if the value of DEFAULT_IP is IP_VERSION4, the command
example% ifconfig -a6
will display all IPv6 interfaces.
EXAMPLES
Example 1: Suppressing IPv6 Related Output
This is what the inet_type file must contain if you want to suppress IPv6 related output:
DEFAULT_IP=IP_VERSION4
SEE ALSO
ifconfig(1M), netstat(1M)
SunOS 5.10 16 Jun 1999 inet_type(4)