08-01-2005
have you removed it or just unconfigured your hme0 interface? see man ifconfig:
# ifconfig hme0 unplumb <-- will remove hme0 from your system
gP
10 More Discussions You Might Find Interesting
1. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT NETBSD
eshconfig
ESHCONFIG(8) BSD System Manager's Manual ESHCONFIG(8)
NAME
eshconfig -- configure Essential Communications' HIPPI network interface
SYNOPSIS
eshconfig [-estx] [-b bytes] [-c bytes] [-d filename] [-i usecs] [-m bytes] [-r bytes] [-u filename] [-w bytes] [interface]
DESCRIPTION
eshconfig is used to configure device-specific parameters and download new firmware to the Essential Communications RoadRunner-based HIPPI
network interface. The interface is very sensitive to the DMA performance characteristics of the host, and so requires careful tuning to
achieve reasonable performance. In addition, firmware is likely to change frequently, which necessitates a reasonably easy way to update
that firmware.
Available operands for eshconfig:
-b bytes
Adjust the burst size for read (by NIC of host memory) DMA.
-c bytes
Adjust the burst size for write (by NIC of host memory) DMA.
-d filename
Filename for file to download into NIC firmware. This must be a file in the standard Essential format, with :04 preceding every
line, and a tag line at the end indicating the characteristics of the firmware file.
-e Write data to EEPROM. Normally, setting tuning parameters will only persist until the system is rebooted. Setting this parameter
ensures that the changes will be written to EEPROM.
-i usecs
Interrupt delay in microseconds.
-m bytes
Minimum number of bytes to DMA in one direction (read or write) before allowing a DMA in the other direction. Tuning this prevents
one direction from dominating the flow of bytes, and artificially throttling the NIC.
-r bytes
Bytes before DMA starts for read (from host to NIC). This controls how soon the DMA is triggered; until this many bytes are
requested, the DMA will not begin.
-s Show statistics for the HIPPI NIC. Repeat the option to suppress non-zero statistics.
-t Show current tuning parameters on the host.
-u filename
Name of file to which the NIC firmware should be uploaded. Not currently supported.
-w bytes
Number of bytes required before write (from NIC to host) DMA is started. Until this many bytes are ready to be written, the DMA will
not start.
-x Reset the NIC. This is necessary for the HIPPI-FP support, as ifconfig(8) will no longer physically reset the NIC when the inter-
faces goes up and down.
Only the super-user may modify the configuration of a network interface.
DIAGNOSTICS
Messages indicating the specified interface does not exist or the user is not privileged and tried to alter an interface's configuration.
SEE ALSO
esh(4), ifconfig(8)
HISTORY
The eshconfig command first appeared in NetBSD 1.4.
BSD
June 17, 2005 BSD