how can i do that in a script withough havin the script halt at the section where the top command is located. am writign a script that will send me the out put of unx commands if the load average of a machine goes beyond the recommended number.
top -n 20
i want to save this output to a file... (1 Reply)
Is there a command in SCO Unix that does the same as the top command in HPUX. The command displays the jobs using the most system resources.
Thanks You (0 Replies)
https://www.unix.com/showpost.php?p=98416&postcount=8
Referring to the post above... what is the unit that is measured in the TOP command under LOAD? (1 Reply)
Hey guys, the top format in HP-UX has the size which is the total virtual size and the res which is the resident size. What are these size and res? (1 Reply)
help! i need help with locating where a program is being run from. when i type top -i it only lists the name and minimal info, not the programs location from where it is being ran. i ask because i just used the same named executable, a.exe for all the processes and have lost the schedule detailing... (4 Replies)
Okay, I am trying to come up with a multi-platform script to report top ten CPU and memory hog processes, which will be run by our enterprise monitoring application as an auto-action item when the CPU and Memory utilization gets reported as higher than a certain threshold
I use top on other... (5 Replies)
Currently when i run top command i get the following columns .
CPU TTY PID USERNAME PRI NI SIZE RES STATE TIME %WCPU %CPU COMMAND
In this how to remove '%WCPU' column ?
Thanks very much in advance . (6 Replies)
Hi All,
i am using the below command and once get the output and i need to keep the
first batch only.in this case how to do this one. please help me on thistop -b -n 5 >top.txt
Thanks, (3 Replies)
Discussion started by: bmk
3 Replies
LEARN ABOUT REDHAT
fdformat
FDFORMAT(8) Linux Programmer's Manual FDFORMAT(8)NAME
fdformat - Low-level formats a floppy disk
SYNOPSIS
fdformat [ -n ] device
DESCRIPTION
fdformat does a low level format on a floppy disk. device is usually one of the following (for floppy devices, the major = 2, and the
minor is shown for informational purposes only):
/dev/fd0d360 (minor = 4)
/dev/fd0h1200 (minor = 8)
/dev/fd0D360 (minor = 12)
/dev/fd0H360 (minor = 12)
/dev/fd0D720 (minor = 16)
/dev/fd0H720 (minor = 16)
/dev/fd0h360 (minor = 20)
/dev/fd0h720 (minor = 24)
/dev/fd0H1440 (minor = 28)
/dev/fd1d360 (minor = 5)
/dev/fd1h1200 (minor = 9)
/dev/fd1D360 (minor = 13)
/dev/fd1H360 (minor = 13)
/dev/fd1D720 (minor = 17)
/dev/fd1H720 (minor = 17)
/dev/fd1h360 (minor = 21)
/dev/fd1h720 (minor = 25)
/dev/fd1H1440 (minor = 29)
The generic floppy devices, /dev/fd0 and /dev/fd1, will fail to work with fdformat when a non-standard format is being used, or if the for-
mat has not been autodetected earlier. In this case, use setfdprm(8) to load the disk parameters.
OPTIONS -n No verify. This option will disable the verification that is performed after the format.
SEE ALSO fd(4), setfdprm(8), mkfs(8), emkfs(8)AUTHOR
Werner Almesberger (almesber@nessie.cs.id.ethz.ch)
Linux 0.99 1 February 1993 FDFORMAT(8)