10-02-2001
Quad Fast Ethernet Card on Sparc 10?
I am having a problem getting my configuration to stick. After I installed my quad-card I did the following:
1. created hostname.qe0, hostname.qe1, hostname.qe2, hostname.qe3 files in my /etc directory.
2. In my /etc/hosts file I added the ip address of each interface and the name for each interface :
216.32.55.67 ext
65.3.2.1 dmz
10.10.10.1 int
172.1.1.1 net
3. In each hostname.qe file I added the hostname associated with each interface.
4. From a terminal I did the following:
ifconfig qe0 216.32.55.67 up
ifconfig qe1 65.3.2.1 up
ifconfig qe2 10.10.10.1 up
ifconfig qe3 172.1.1.1 up
***After I do all this it works fine
~~~Once I reboot my machine....it loses all of the settings for the Quad-Card.
Have any of you ever run into this or am I doing anything noticibly
wrong? Any help on this would be great.
Thanks,
Jeff
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
arp(1M) System Administration Commands arp(1M)
NAME
arp - address resolution display and control
SYNOPSIS
arp hostname
arp -a [-n]
arp -d hostname
arp -f filename
arp -s hostname ether_address [temp] [pub] [trail]
DESCRIPTION
The arp program displays and modifies the Internet-to-MAC address translation tables used by the address resolution protocol (see arp(7P)).
With no flags, the program displays the current ARP entry for hostname. The host may be specified by name or by number, using Internet dot
notation.
OPTIONS
-a Display all of the current ARP entries. The definition for the flags in the table are:
M Mapping; only used for the multicast entry for 224.0.0.0
P Publish; includes IP address for the machine and the addresses that have explicitly been added by the -s option. ARP will
respond to ARP requests for this address.
S Static; not learned for the ARP protocol.
U Unresolved; waiting for ARP response.
You can use the -n option with the -a option to disable the automatic numeric IP address-to-name translation. Use arp -an or arp
-na to display numeric IP addresses.
-d Delete an entry for the host called hostname. This option may only be used by the super-user.
-f Read the file named filename and set multiple entries in the ARP tables. Entries in the file should be of the form:
hostname MACaddress [temp] [pub] [trail]
See the -s option for argument definitions.
-s Create an ARP entry for the host called hostname with the MAC address MACaddress. For example, an Ethernet address is given as
six hexadecimal bytes separated by colons. The entry will be permanent unless the word temp is given in the command. If the word
pub is given, the entry will be published. For instance, this system will respond to ARP requests for hostname even though the
hostname is not its own. The word trail indicates that trailer encapsulations may be sent to this host. arp -s can be used for a
limited form of proxy ARP when a host on one of the directly attached networks is not physically present on the subnet. Another
machine can then be configured to respond to ARP requests using arp -s. This is useful in certain SLIP configurations.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
ifconfig(1M), arp(7P), attributes(5)
SunOS 5.10 7 Mar 2003 arp(1M)