10-02-2001
sys-unconfig
well I ran sys-unconfig and when it runs ifconfig it times out on my interface (hme0) so then nothing gets configured. it says that my interface is not configured properly. then it dumps core and runs rpc services and hangs. at this point I have to power down. any thoughts?
10 More Discussions You Might Find Interesting
1. IP Networking
I have managed to setup my Solaris box to receive an IP number from a DHCP server. In addition, I can ping and telnet between my dhcp server and my solaris box using the IP number. However, I can't resolve addresses by name from my solaris box.
In my nsswitch.conf file I have:
hosts: dns
... (4 Replies)
Discussion started by: marist89
4 Replies
2. Solaris
How is it possible to derive the very next IP that the solaris dhcp server is going to assign to the next host that requests? (0 Replies)
Discussion started by: ne0phyte
0 Replies
3. Solaris
Can any one tell me how to stop DHCP service on Solaris 10 so that it should not start nextime when the system is rebooted. (2 Replies)
Discussion started by: shabu
2 Replies
4. Solaris
I am trying to set up a DHCP on Sunblade 100. I have Dlink router that connects me to the net with my other computers. I can't seem to let my DHCP server to give out IP addresses instead of my router. I have been working on this for the last three days. I had an issue with Unknown name but i have... (4 Replies)
Discussion started by: aliban83
4 Replies
5. UNIX for Dummies Questions & Answers
I have a new solaris machine and I am trying to bring the same on network. The IP assignemnt is via DHCP. I want to know as which files need to be modified to include DHCP server IP in order that the machine gets its IP via DHCP server.
Thanks in Advance. :) (1 Reply)
Discussion started by: Ashvin Gaur
1 Replies
6. Solaris
Hello,
I need to configure a Cisco VLAN Accesspoint with DHCP using Solaris
dhtadm & pntadm
Network: 10.10.122.0 255.255.255.0
Default Router 10.10.122.1
Scope Range 10.10.122.10 - 254
Option 60 “Cisco AP c1142”
Option 43 ... (0 Replies)
Discussion started by: fredy82
0 Replies
7. Solaris
Dear All,
I have following configuration solaris 10 host
interface e1000g0 hold IP 10.124.73.178 having internet access natted to public ip on cisco switch
interface e1000g1 hold IP 192.168.8.10 DHCP server with DHCP client IP ranges 192.168.8.11 to 192.168.8.15
/etc/defaultrouter hold... (4 Replies)
Discussion started by: patel1678
4 Replies
8. Solaris
I need to find out the MAC address of an IP leased from DHCP server .
For Eg:-i need to know the MAC of the below mentioned IP at the below mentioned time .
IP : 172.16.28.90
Date :Sunday July 2nd 2011
Time : 14.07.2011
OS -Solaris 10
Vital QIP IP management software using to... (0 Replies)
Discussion started by: sandeep.tk
0 Replies
9. Solaris
Hi All,
Could you please let me know how can we check whether any given solaris machien is using DHCP or not.
is ps -ef | grep dhcp is full proof method or is their any other way. (10 Replies)
Discussion started by: omkar.jadhav
10 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LEARN ABOUT V7
sys-unconfig
sys-unconfig(1M) System Administration Commands sys-unconfig(1M)
NAME
sys-unconfig - undo a system's configuration
SYNOPSIS
/usr/sbin/sys-unconfig
DESCRIPTION
The sys-unconfig command is used to restore a system's configuration to an "as-manufactured" state, ready to be reconfigured again. The
system's configuration consists of hostname, Network Information Service (NIS) domain name, timezone, IP address, IP subnet mask, and root
password. This operation is the inverse of those performed by the sysidnet(1M), sysidns(1M), and sysidsys(1M) programs run at boot. See
sysidtool(1M).
sys-unconfig does the following:
o Saves current /etc/inet/hosts file information in /etc/inet/hosts.saved.
o If the current /etc/vfstab file contains NFS mount entries, saves the /etc/vfstab file to /etc/vfstab.orig.
o Restores the default /etc/inet/hosts file.
o Removes the default hostname in /etc/hostname.interface files for all interfaces configured when this command is run. To determine
which interfaces are configured, run the command 'ifconfig-a'. The /etc/hostname.interface files corresponding to all of the inter-
faces listed in the resulting output, with the exception of the loopback interface (lo0), will be removed.
o Removes the default domainname in /etc/defaultdomain.
o Restores the timezone to PST8PDT in /etc/TIMEZONE.
o Disables the Network Information Service (NIS) and Network Information Service Plus (NIS+) if either NIS or NIS+ was configured.
o Removes the file /etc/inet/netmasks.
o Removes the file /etc/defaultrouter.
o Removes the password set for root in /etc/shadow.
o Removes the file /etc/.rootkey.
o Executes all system configuration applications. These applications are defined by prior executions of a sysidconfig -a application.
(See sysidconfig(1M)). When sys-unconfig is run, all system configuration applications are passed one argument, -u.
o Removes the file /etc/resolv.conf.
o Disables LDAP by removing /var/ldap/ldap_client_cache, /var/ldap/ldap_client_file, /var/ldap/ldap_client_cred, and
/var/ldap/cachemgr.log.
o Regenerates keys for sshd(1M).
When sys-unconfig is finished, it performs a system shutdown. sys-unconfig is a potentially dangerous utility and can only be run by the
super user.
FILES
/etc/default/init process control initialization
/etc/defaultdomain
/etc/defaultrouter
/etc/hostname.interface
/etc/inet/hosts host name database
/etc/inet/netmasks network mask database
/etc/nodename
/etc/.rootkey super-user's secret key
/etc/shadow shadow password file
/etc/vfstab virtual file system table
/var/nis/NIS_COLD_START
/var/yp/binding/*/ypservers
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWadmap |
+-----------------------------+-----------------------------+
SEE ALSO
init(1M), kdmconfig(1M), sshd(1M), sysidconfig(1M), sysidtool(1M), hosts(4), netmasks(4), shadow(4), attributes(5)
NOTES
sys-unconfig is not available on diskless clients.
SunOS 5.10 4 Jun 2004 sys-unconfig(1M)