07-01-2005
you could write it in one of your startscripts....
gP
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
3. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)
NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD
April 11, 1998 BSD