07-01-2005
you could write it in one of your startscripts....
gP
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
3. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT HPUX
pthread_rwlockattr_init
pthread_rwlockattr_init(3T) pthread_rwlockattr_init(3T)
NAME
pthread_rwlockattr_init(), pthread_rwlockattr_destroy() - initialize or destroy a read-write lock attributes object
SYNOPSIS
PARAMETERS
attr Pointer to the read-write lock attributes object to be initialized or destroyed.
DESCRIPTION
initializes the read-write lock attributes object attr with the default value for all attributes. The attributes object describes a read-
write lock in detail and is passed to the read-write lock initialization function.
When a read-write lock attributes object is used to initialize a read-write lock, the values of the individual attributes determine the
characteristics of the new read-write lock. Attributes objects act like additional parameters to object initialization.
After a read-write lock attributes object has been used to initialize one or more read-write lock, any function affecting the attributes
object does not affect the previously initialized read-write locks.
The read-write lock attributes and their default values are:
The default value is
If an initialized read-write lock attributes object is reinitialized, undefined behavior results.
destroys the read-write lock attributes object attr. The destroyed read-write lock attributes object ceases to exist and its resources are
reclaimed. Referencing the object after it has been destroyed results in undefined behavior. A destroyed read-write lock attributes object
can be reinitialized using the function
Read-write locks which have been already initialized using this attributes object are not affected by the destruction of the read-write
lock attributes object.
RETURN VALUE
Upon successful completion, and return zero. Otherwise, an error number is returned to indicate the error (the variable is not set).
ERRORS
For each of the following conditions, if the condition is detected, the and functions return the corresponding error number:
[ENOMEM] There is insufficient memory available in which to initialize attr.
[EINVAL] The value specified by attr is invalid.
AUTHOR
and were developed by X/Open.
SEE ALSO
pthread_create(3T), pthread_rwlockattr_getpshared(3T), pthread_rwlockattr_setpshared(3T), pthread_rwlock_init(3T).
STANDARDS CONFORMANCE
Pthread Library pthread_rwlockattr_init(3T)