06-28-2005
still didnt work
i tried to execute the file and it says: cannot execute
also keep in mind that a reinstall is not and option because during the install disk 1 ejected before it stopped spinning and got ruined but i really would like to get to my desktop... heres some specs on my computer
Dell optiplex GX 270
Intel Inside Pentium 4 processor (2.66 ghz)
the graphics card DOES show up in the system config
only thing that doesnt work is when it atemps to configure the network address...(dont worry about it that problem though)
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
I need help editing my openwin file. I've got it all set up so the options I normally use (xman, cmdtools, xeyes, printtool) automatically come up when I log on, but it won't read my -geometry entries. I got them by right-clicking on the desktop, but apparently they need to be entered a certain... (0 Replies)
Discussion started by: sdienlin
0 Replies
2. UNIX for Dummies Questions & Answers
I am a newb linux user. And i am running suse 9.3 pro.
When i first installed it a couple of days ago, it booted into the desktop
fine the first four or five times.
And not when i turn on my computer and boot linux and loads the devices, then it prompts me...
UserName:
Password:
(which... (1 Reply)
Discussion started by: derekmpage
1 Replies
3. UNIX for Dummies Questions & Answers
hey. i was wondering if some one could tell me how to get install this on my open suse linux.
http://en.opensuse.org/Xgl
it looks pretty handy, but im new to linux and im unsure how to proceed.
thanks (0 Replies)
Discussion started by: bebop1111116
0 Replies
4. UNIX for Advanced & Expert Users
i want to access my group users desktop.
can i did that by using xwd and xwud? else what can i do for that? (0 Replies)
Discussion started by: lakshmananindia
0 Replies
5. Solaris
Hi friends, i had small problem in my home pc i install solaris 10 but GUI is very big cannot view any thing, but i can open terminal where with very difficulty is there any command to re size my resolution some thing like 1024. if not i want to log in default console other than GUI only terminal... (5 Replies)
Discussion started by: kurva
5 Replies
6. UNIX for Dummies Questions & Answers
How to set up a framebuffer desktop (environment) / no X desktop (environment)? In my case: Debian etch, allready with framebuffer but I mean that I have in framebuffer all I use in X - also read pdf (without hanging up the whole system..) and so on. (3 Replies)
Discussion started by: Action
3 Replies
7. What is on Your Mind?
I am on Solaris 10
cat /etc/release
Solaris 10 10/09 s10x_u8wos_08a X86
Copyright 2009 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to license terms.
Assembled 16 September 2009 (16 Replies)
Discussion started by: solaris_user
16 Replies
8. UNIX Desktop Questions & Answers
We are going to use Linux Desktop systems.
Which one will be the best option ?
I prefer CentOS , but in CentOS which one ?
I heard fedora will take more Ram space..!! is it ?
P.S
1. Users are developers , with eclipse , java , tomcat webserver etc.
2. System Configuration ~: 2GB ,... (8 Replies)
Discussion started by: linuxadmin
8 Replies
9. Linux
Right, I know this topic has more or less been done to death, however, I'm bringing it up again.
I'm planning on moving to Linux as a full time desktop OS for my home system.
I don't want to run a security distro, or anything that runs as root and just use my Windows OS in a VM when I need to use... (11 Replies)
Discussion started by: 3therk1ll
11 Replies
EX(4) BSD/i386 Kernel Interfaces Manual EX(4)
NAME
ex -- Ethernet device driver for the Intel EtherExpress Pro/10 and Pro/10+
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ex
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ex_load="YES"
DESCRIPTION
The ex driver provides support for Ethernet adapters based on the Intel i82595 chip.
On the ISA bus, the card will be searched for in the I/O address range 0x200 - 0x3a0. The IRQ will be read from the EEPROM on the card. For
correct operation Plug-N-Play support should be disabled.
On the PC Card bus, the card will be automatically recognized and configured.
HARDWARE
The ex driver supports the following Ethernet adapters:
o Intel EtherExpress Pro/10 ISA
o Intel EtherExpress Pro/10+ ISA
o Olicom OC2220 Ethernet PC Card
o Olicom OC2232 Ethernet/Modem PC Card
o Silicom Ethernet LAN PC Card
o Silicom EtherSerial LAN PC Card
DIAGNOSTICS
ex%d: Intel EtherExpress Pro/10, address %6D, connector %s The device probe found an installed card, and was able to correctly install the
device driver.
ex%d: WARNING: board's EEPROM is configured for IRQ %d, using %d The device probe detected that the board is configured for a different
interrupt than the one specified in the kernel configuration file.
ex%d: invalid IRQ. The device probe detected an invalid IRQ setting.
SEE ALSO
arp(4), netintro(4), ng_ether(4), ifconfig(8)
HISTORY
The ex device driver first appeared in FreeBSD 2.2.
AUTHORS
The ex device driver was written by Javier Martin Rueda. The PC Card attachment was written by Mitsuru ISAWAKI and Warner Losh. This manual
page was written by David E. O'Brien.
BUGS
Currently the driver does not support multicast.
The Silicom EtherSerial card's serial port does not currently work. The Olicom OC2232 PC Card should work with the ex driver, but is cur-
rently completely broken.
BSD
July 16, 2005 BSD